BMW 3 Touring 320 I

Welcome to CVJoint24, your Swedish driveline specialist for the BMW 3 Touring 320 I. We supply a comprehensive range of high-grade components to ensure your vehicle's power transfer...

Products for BMW 3 Touring 320 I

10 products
1 - 10 of 10
Item no.:512680
  • Position: Rear right
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 805 mm
  • Joint diameter: 77 mm
Item no.:518063
  • Position: Rear right
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 793 mm
  • Joint diameter: 90 mm
Item no.:412937
  • Position: Rear left
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 739 mm
  • Joint diameter: 90 mm
Item no.:513523
  • Position: Rear right
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 800 mm
Item no.:646169
  • Position: Rear, Inner
  • Inner splines: 24
  • Total length: 24 mm
  • Thread size: M24X1,5
Item no.:652345
  • Position: Rear, Outer
  • Inner splines: 24
  • Seal diameter: 69 mm
  • Outer splines: 27
  • ABS teeth: 48
Item no.:7316329
  • Position: Rear left
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 751 mm
  • Joint diameter: 84 mm

Drivetrain for BMW 3 Touring 320 I

The BMW 3 Touring 320 I represents a fine balance between practical versatility and sporty driving dynamics. As the owner of such an estate, you know that every component in the drivetrain must work in harmony to preserve that distinctive driving experience. The drivetrain is at the very core of your car's power transfer, and on an estate model—frequently used for longer journeys and carrying heavier loads—these parts are exposed to substantial stresses. At CVJoint24, we take pride in being your Swedish driveline specialist for these precise components. Our focus is on supplying parts that not only fit physically, but also perform reliably under demanding European road conditions.

By choosing specialised parts, you ensure that your BMW retains its precise steering and sharp acceleration. We have built extensive expertise around BMW drivetrains, enabling us to offer a deep range tailored specifically to the 320 I model. Maintaining the drivetrain is not merely a matter of performance, but also one of safety and long-term cost efficiency, as worn components can lead to secondary damage across more expensive assemblies such as the gearbox and differential.

How the drivetrain is engineered on the BMW 3 Touring 320 I

The layout of the drivetrain in a BMW 3 Touring 320 I is a masterpiece of engineering, where each part has a specific task to deliver power cleanly to the road. The system begins at the gearbox and runs rearwards via the propeller shaft. To keep the prop shaft stable and free from vibrations, a centre bearing is used, and we offer this part in several versions to match different technical specifications. Continuing out towards the wheels, we find the drive shafts, which serve as the final links in the chain.

A drive shaft for the BMW 3 Touring 320 I consists of a shaft bar fitted with two joints. The inner CV joint sits closest to the differential and allows the shaft to plunge axially as the suspension moves. The outer CV joint sits at the wheel hub, facilitating steering while maintaining constant drive. This entire system is protected by rubber CV boots that retain the vital grease and keep out moisture and dirt, which is absolutely crucial for the longevity and function of these components over time.

Common faults and symptoms

Identifying drivetrain issues early can save you from far more expensive repairs down the line. For a BMW 3 Touring 320 I, the most common warning signs are easily heard and felt. If you notice a rhythmic clicking sound during tight turns, such as at a junction or while parking, it is a classic symptom of a worn outer constant velocity joint. Vibrations felt through the seat or steering wheel under acceleration often point to worn inner joints or an imbalance in a driveshaft, usually caused by pitted or uneven inner bearing surfaces.

If vibrations occur at specific cruising speeds and feel more like a droning sensation throughout the cabin, attention should turn to the propeller shaft centre bearing. Another vital sign is grease splattered across the inside of the wheel rim or wheel arch, indicating a split CV boot. Once the grease escapes, friction quickly destroys the hardened surfaces inside the joint. Regular inspection of these components provides inexpensive peace of mind, particularly ahead of longer journeys where drivetrain loads increase.

Common parts to replace on the BMW 3 Touring 320 I

When replacement is due, CVJoint24 makes it simple by providing the most relevant parts for your BMW 3 Touring 320 I. Our catalogue currently features carefully selected components covering the most frequent requirements for this model. We offer 3 different complete drive shafts, which is often the most time-efficient repair option because you receive both inner and outer joints pre-assembled and ready to fit.

For those who prefer to address only the specific point of failure, we stock premium-quality outer CV joints and inner CV joints. Furthermore, we keep several variants of centre bearings in stock, as these can vary depending on your car's exact build date and chassis number. Choosing the correct replacement is not just about physical fitment, but also ensuring adequate strength to manage the torque output of the 320 I. All our parts are thoroughly tested to guarantee they meet the high standards demanded by a modern BMW drivetrain.

Finding the right part for your BMW 3 Touring 320 I

Select your category below for the BMW 3 Touring 320 I:

On a vehicle where drivetrain issues can stem from several areas, starting in the correct category is essential. By comparing the exact sections for the BMW 3 Touring 320 I, it is straightforward to differentiate between drive shaft, CV joint, or prop shaft faults, allowing you to proceed directly to the page that matches your symptoms and requirements.

When browsing our products, you will find clear technical specifications and detailed line drawings. We encourage our customers to verify details such as spline counts (teeth) and overall length if multiple versions are listed for your vehicle. Should you feel unsure, our specialist team is always ready to assist. We understand that a BMW owner values engineering precision, and our fitment guarantee gives you complete confidence that the car parts you order will work seamlessly with your existing setup without modifications.

Why shop at CVJoint24?

Choosing CVJoint24 means selecting dedicated technical expertise and quality over generic car parts. We are a Swedish specialist passionate about drivetrains and power transfer, with our main warehouse in Helsingborg, Sweden, shipping directly across the EU. We understand how important it is to receive the correct item the first time, which is why we continually refine our product data and technical descriptions.

Our fitment guarantee ensures complete peace of mind when selecting parts using your car's make, model and engine variant. By shopping with us, you are supported by experts who have the technical knowledge to answer detailed queries, something often missing with general retailers. CVJoint24 is your reliable partner for a dependable, high-performing drivetrain, whether you tackle the job yourself or hand the parts to your local garage. With our focus on durability and quality, we ensure your BMW remains the engaging machine it was built to be.

Frequently Asked Questions about Drivetrain for BMW 3 Touring 320 I

Which parts make up the drivetrain on a BMW 3 Touring 320 I?

The drivetrain mainly consists of drive shafts, inner and outer CV joints, and a propeller shaft with its centre bearing. These components work together to transfer power from the gearbox to the wheels.

How do I know if my outer CV joint needs replacing?

A common symptom is a clicking noise when cornering sharply. If you also notice that the CV boot is split and grease has escaped, it is high time to replace the joint before it fails completely.

Why does my BMW 3 Touring 320 I vibrate under acceleration?

Vibrations during acceleration are frequently caused by wear in the inner CV joints. They can also stem from an unbalanced drive shaft or an issue with the propeller shaft centre bearing.

Do all drive shafts fit every 320 I model?

No, there can be variations depending on model year and gearbox type. Always select your car's make, model and engine to ensure you get a part with the correct length and tooth count.

What is the benefit of buying a complete drive shaft?

Buying a complete drive shaft saves time during installation because the joints are already pre-assembled and greased. It also eliminates the risk of overlooking wear on whichever joint you were not intending to replace.

Do you offer a guaranteed fit for BMW parts?

Yes, we offer a guaranteed fit on all our drivetrain components when you select your vehicle's make, model and engine to identify the correct part for your BMW 3 Touring 320 I.