Isuzu Gemini

Spare parts and drivetrain components for Isuzu Gemini.

Products for Isuzu Gemini

19 products
1 - 19 of 19
Item no.:0530344
  • Position: Front left, Outer
  • Inner splines: 22
  • Splines wheel side: 22
  • Seal diameter: 50 mm
  • Outer splines: 22
Item no.:0555257
  • Position: Front right, Outer
  • Inner splines: 21
  • Seal diameter: 50 mm
  • Outer splines: 22
  • Thread size: M22X1,5
Item no.:0389421
  • Position: Front
  • ABS teeth: 42
  • Inner diameter: 79 mm
  • Outer diameter: 87 mm
  • Width: 12 mm
Item no.:0542858
  • Position: Outer
  • Inner splines: 23
  • Splines wheel side: 24
  • Seal diameter: 50 mm
  • Outer splines: 24
Item no.:0554800
  • Position: Outer
  • Inner splines: 23
  • Splines wheel side: 24
  • Seal diameter: 50 mm
  • ABS teeth: 42
Item no.:0606805
  • Total length: 84 mm
Item no.:390083
  • Position: Front
  • Inner diameter: 34 mm
  • Outer diameter: 55 mm
Item no.:0546887
  • Position: Outer
  • Inner splines: 21
  • Seal diameter: 52 mm
  • Outer splines: 22
  • Thread size: M22X1,5
Item no.:1154072
  • Position: Front left
  • Splines gearbox side: 34
  • Splines wheel side: 22
  • Joint diameter: 79 mm
  • Joint diameter, gearbox side: 74 mm
Item no.:2159391
  • Position: Front right
  • Splines gearbox side: 34
  • Splines wheel side: 22
  • Joint diameter: 74,6 mm
  • Joint diameter, gearbox side: 74 mm
Item no.:1152274
  • Position: Front left
Item no.:2127754
  • Position: Front right
Item no.:0348607
  • Position: Front
  • ABS teeth: 42
  • Inner diameter: 79 mm
  • Outer diameter: 87 mm
  • Width: 12 mm
Item no.:0598258
  • Position: Outer
  • Inner splines: 23
  • Splines wheel side: 24
  • Seal diameter: 50 mm
  • Outer splines: 24
Item no.:0583738
  • Position: Outer
  • Inner splines: 23
  • Splines wheel side: 24
  • Seal diameter: 50 mm
  • ABS teeth: 42
Item no.:0664631
  • Total length: 84 mm
Item no.:0592783
  • Position: Outer
  • Inner splines: 21
  • Seal diameter: 52 mm
  • Outer splines: 22
  • Thread size: M22X1,5
Item no.:0696422
  • Total length: 84 mm
Item no.:0609739
  • Total length: 84 mm

Drivetrain for Isuzu Gemini

The Isuzu Gemini is a car that demands precision and attention to detail when maintaining its power transmission parts. As a Swedish drivetrain specialist, we understand the importance of supplying components that match original specifications exactly to preserve your car's genuine handling. Whether you own a classic Isuzu Gemini or a later edition, the condition of the drivetrain is crucial for both road safety and overall ride comfort. We focus on providing parts that ensure power is transferred smoothly from the engine to the wheels without unnecessary energy loss, vibrations, or unwanted noises. Choosing the right components prolongs your car's service life and prevents costly consequential damage to other suspension parts.

How the Isuzu Gemini drivetrain is built

The drivetrain in an Isuzu Gemini is engineered to be both compact and dependable, reflecting classic Japanese automotive design of its era. The system typically centres on a transversely mounted engine that delivers drive to the front wheels via a gearbox. This front-wheel-drive configuration means the drive shafts must cope with substantial torque transfer as well as wide steering angles. Each drive shaft is fitted with two joints: an inner joint that seats against the gearbox and an outer joint at the wheel hub. The outer unit is a constant velocity joint (CV joint), which allows the road wheel to turn at a uniform speed regardless of the steering lock. Understanding how these parts interact is vital when diagnosing chassis and driveline faults.

Common faults and symptoms

Several clear warning signs show when components in your Isuzu Gemini drivetrain are worn and require attention. One of the most typical symptoms is a rhythmic clicking or knocking noise clearly audible during tight turns at low speeds. This sound almost invariably indicates that an outer CV joint is worn or contaminated with dirt. If you experience vibrations through the steering wheel or bodywork under acceleration instead, this often points to worn inner CV joints or a bent drive shaft. It is equally important to inspect the CV boots regularly; if a boot splits, lubricating grease escapes whilst water and road dirt enter, quickly ruining the joint.

Common parts to replace on the Isuzu Gemini

For the Isuzu Gemini, front driveline components face the heaviest daily stresses. The most vital and frequently replaced part in our range for this model is the outer CV joint. Because this specific joint must accommodate vertical wheel movement from the suspension alongside horizontal steering motion, it is usually the first component to wear out. Our catalogue offers carefully chosen parts built to handle the torque and loads produced by the Gemini engine. Replacing a worn constant velocity joint promptly prevents full driveshaft failure, saving you both time and workshop expenses.

Find the right part for your Isuzu Gemini

Select the relevant section for your Isuzu Gemini below:

On a vehicle where several drivetrain faults can occur, starting in the correct category makes diagnosis straightforward. Comparing the specific subcategories for the Isuzu Gemini helps you tell drive shaft, CV joint, or prop shaft issues apart and proceed directly to the parts matching your symptoms and technical specifications.

Why buy from CVJoint24?

CVJoint24 is your dedicated specialist for Japanese car transmissions and driveline parts. As a Swedish drivetrain specialist dispatching orders across the EU from our warehouse in Helsingborg, Sweden, we combine a focused, comprehensive inventory with specialist technical knowledge. We recognise the unique requirements of every vehicle and curate our range to satisfy rigorous quality standards. When you order from us, you gain access to durable car parts engineered for an exact fit. We take pride in keeping vehicles across Europe running reliably with safe, efficient drivetrains—whether for daily drivers or cherished classics like the Isuzu Gemini.

Frequently Asked Questions about Drivetrain for Isuzu Gemini – Find the Right Spare Parts

How do I know if my Isuzu Gemini needs a new outer CV joint?

The most common symptom is a clicking or knocking noise from the front suspension when taking sharp turns while driving.

How do I find parts that fit my Isuzu Gemini?

Simply select your Isuzu Gemini make, model and engine variant in our store to filter parts with guaranteed correct fitment.

Why does my car vibrate under acceleration?

Vibrations during acceleration are often caused by wear in the inner CV joints or an imbalance in the drive shaft itself.

Is it important to replace a damaged CV boot immediately?

Yes, a split CV boot allows grease to escape and dirt to penetrate, which quickly destroys the CV joint and leads to more expensive repairs.

Which drivetrain categories are available for the Isuzu Gemini?

At present, we primarily offer outer CV joints, which are among the most critical wear parts in the Isuzu Gemini drivetrain.

What should I consider when installing a new CV joint?

Always check that the number of splines on the new joint matches your original shaft, and ensure that the ABS ring, if fitted, is correctly positioned.