Mazda E Serie

Welcome to CVJoint24, your driveline specialist for the Mazda E Serie. As Swedish driveline experts, we focus on providing the exact replacement components needed for your vehicle's...

Products for Mazda E Serie

14 products
1 - 14 of 14
Item no.:628900
  • Total length: 57 mm
  • Diameter: 32 mm
Item no.:355910
  • Position: Front, Outer
  • Inner splines: 23
  • Seal diameter: 65 mm
  • Outer splines: 26
  • Joint diameter: 83 mm
Item no.:0931815
  • Diameter: 26,5 mm
Item no.:0957384
  • Inner diameter: 33 mm
  • Outer diameter: 56 mm
Item no.:0636859
  • Total length: 90 mm
Item no.:0652048
  • Total length: 84 mm
Item no.:3559295
  • Position: Outer
  • Inner splines: 21
  • Seal diameter: 56 mm
  • Outer splines: 26
  • Thread size: M22X1,5
Item no.:1187230
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 26
  • Total length: 622 mm
Item no.:1133775
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 26
  • Total length: 622 mm
  • ABS teeth: 44
Item no.:2177946
  • Position: Front right
  • Splines gearbox side: 24
  • Splines wheel side: 26
  • Total length: 895 mm
  • Joint diameter: 73 mm
Item no.:2148450
  • Position: Front right
  • Splines gearbox side: 24
  • Splines wheel side: 26
  • Total length: 895 mm
  • ABS teeth: 44

Drivetrain for Mazda E Serie

The Mazda E Serie is a classic workhorse that has served for decades as a dependable commercial van for businesses and private owners alike. For a vehicle such as the Mazda E Serie to deliver its expected performance and durability, an intact drivetrain in top condition is essential. The transmission system delivers the engine's power to the wheels, and in a commercial vehicle these components endure significantly higher loads than in a passenger car. As an owner of a Mazda, you know that mechanical simplicity is often the secret to a long service life, yet even the sturdiest setups need regular maintenance. At CVJoint24, we specialise in supplying car parts specifically developed to cope with the heavy payloads and varied road conditions this model faces. We ensure you have access to components that preserve the vehicle's original reliability and driving feel.

How the drivetrain is configured on the Mazda E Serie

The drivetrain layout on the Mazda E Serie is engineered around torque and long-term endurance. Most models in the range feature a traditional rear-wheel-drive configuration with a longitudinally mounted engine. Power travels from the gearbox via a propeller shaft to a rear axle differential, which in turn distributes power to the rear wheels through drive shafts. This layout is ideal for commercial vans as it provides better traction when carrying heavy loads. Four-wheel-drive versions add a transfer box and front driveshafts with matching CV joints. Every link in this chain, from universal joints to wheel bearings, must work in perfect harmony. Understanding this mechanical setup is key to carrying out correct servicing. We supply the technical components required to maintain both the straightforward rear-wheel drive and the more complex four-wheel-drive systems, always engineered for a precise fit on your Mazda.

Common faults and symptoms

Several clear signs indicate that your Mazda E Serie drivetrain is wearing out and requires attention. One of the most frequent symptoms is vibration through the chassis while driving, which can often be traced back to an unbalanced prop shaft or a worn centre bearing. If you notice a clicking or knocking sound on full steering lock, it is a classic sign of play in an outer CV joint. On a commercial vehicle, monitoring for leaks is also crucial; grease splatters on the inside of the road wheels or under the chassis often point to a split CV boot. Another common issue is differential noise, typically heard as a whine or hum that alters with road speed. Ignoring these warning signs can lead to total breakdown, leaving your van out of action in the middle of a working day. Early diagnosis and replacing worn parts saves both time and money in the long run.

Common parts to replace on the Mazda E Serie

When maintaining a Mazda E Serie, certain components face heavier wear than others due to the vehicle's demanding working life. One of the most critical parts to inspect regularly is CV boots for Mazda E Serie. These protective rubber boots retain grease within the constant velocity joints while sealing out grit, moisture and road salt. As rubber perishes and cracks over time, boots inevitably split, which quickly ruins the joint inside. Alongside boots, universal joints for the prop shaft and centre bearings are common wear items that must be replaced to cure driveline vibrations. We ensure our spare parts meet high standards that easily withstand demanding European winters and the rigours of commercial duties. Proactively fitting an inexpensive replacement such as a CV joint boot helps you prevent costly damage to complete drive shafts or differentials later on.

How to find the right part for your Mazda E Serie

Select the relevant category for your Mazda E Serie:

On a vehicle with several possible driveline symptoms, starting in the right section saves time. By comparing the exact component sections for the Mazda E Serie, it is straightforward to distinguish between faults in a drive shaft, CV joint or propeller shaft and proceed directly to the page that matches your symptoms and fitment.

Our catalogue is built to give you confidence at every stage, from vehicle lookup to delivery, helping your Mazda E Serie get back to work without delay.

Why choose CVJoint24

CVJoint24 is not just an ordinary car parts seller; we are the international store of a Swedish driveline specialist, focused entirely on drivetrain and power transmission components. When ordering from us, you benefit from genuine expertise that ensures you get the right part every time. We know that your Mazda E Serie is a vital tool for your daily work, which is why we emphasise accuracy and dependable dispatch from our central Swedish warehouse. With our fitment guarantee, you can order with complete peace of mind, knowing your components will fit your van perfectly. Combining quality products with competitive prices and customer support that understands driveline engineering, we are the trusted choice for both independent garages and DIY mechanics. Choose CVJoint24 for a straightforward experience that keeps your vehicle performing at its best.

Frequently asked questions about drivetrain parts for Mazda E Serie

How do I know if a CV boot on my Mazda E Serie is split?

The easiest way is to inspect the boot visually for cracks or splits. Another clear sign is finding grease splattered on the inside of the wheel rim or around the wheel arch, which indicates that the lubricating grease has leaked out.

Can I search by make, model and engine to find parts for Mazda E Serie?

Yes, selecting your car by make, model and engine variant is the most reliable way to find parts that fit your specific model year and engine type of the Mazda E Serie.

What happens if I drive with a split CV boot?

If the CV boot is damaged, dirt and water penetrate the CV joint while the grease escapes. This leads to rapid wear, abnormal noises and ultimately complete failure of the constant velocity joint, which is far more expensive to repair than simply replacing the boot.

Do you offer a fitment guarantee on parts for Mazda E Serie?

Yes, we always provide a fitment guarantee when you select your vehicle by make, model and engine. This means we guarantee that the part you order is compatible with your car.

What are the most common signs of drivetrain wear on a commercial van?

Vibrations during acceleration, clicking noises when cornering and whining sounds from the rear axle are the most common signs that drivetrain components need checking or replacing.

How quickly will my spare parts be delivered?

We dispatch our stocked items as quickly as possible from our central warehouse, so you can get your Mazda E Serie back on the road without delay.