Peugeot Bipper

Spare parts and drivetrain components for the Peugeot Bipper.

Products for Peugeot Bipper

23 products
1 - 23 of 23
Item no.:1187002
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 25
  • Total length: 655 mm
  • Joint diameter: 81,4 mm
Item no.:0514788
  • Position: Outer
  • Inner splines: 22
  • Seal diameter: 51 mm
  • Outer splines: 25
  • Thread size: M24X1,5
Item no.:0630107
  • Outer diameter: 22 mm
  • Diameter: 78 mm
Item no.:148309
  • Position: Inner
  • Inner splines: 22
  • Splines gearbox side: 22
  • Total length: 159 mm
Item no.:247586
  • Position: Inner
  • Splines gearbox side: 22
  • Splines wheel side: 22
  • Total length: 196 mm
  • ABS teeth: 22
Item no.:2198147
  • Position: Front right
  • Splines gearbox side: 22
  • Splines wheel side: 25
  • Total length: 885 mm
  • Joint diameter: 79 mm
Item no.:1180130
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 25
  • Total length: 605 mm
  • Joint diameter: 84 mm
Item no.:2123342
  • Position: Front right
  • Splines gearbox side: 24
  • Splines wheel side: 25
  • Total length: 920 mm
  • Joint diameter: 84 mm
Item no.:0555441
  • Position: Outer
  • Inner splines: 24
  • Seal diameter: 51 mm
  • Outer splines: 25
  • Thread size: M24X1,5
Item no.:1175198
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 22
  • Total length: 650 mm
  • Joint diameter: 79 mm
Item no.:2184837
  • Position: Front right
  • Splines gearbox side: 22
  • Splines wheel side: 22
  • Total length: 881 mm
  • Joint diameter: 79 mm
Item no.:0697020
  • Outer diameter: 19 mm
  • Diameter: 76 mm
Item no.:153569
  • Position: Outer
  • Inner splines: 22
  • Seal diameter: 51 mm
  • Outer splines: 22
  • Thread size: M22X1,5
Item no.:0625906
  • Outer diameter: 19 mm
Item no.:3562464
  • Position: Outer
  • Inner splines: 22
  • Splines wheel side: 22
  • Outer diameter: 79 mm
Item no.:345984
  • Position: Front, Inner
  • Inner splines: 24
  • Splines gearbox side: 24
  • Seal diameter: 29,7 mm
  • Total length: 493 mm
Item no.:242859
  • Position: Front right, Inner
  • Inner splines: 22
  • Splines gearbox side: 22
  • Seal diameter: 43,1 mm
  • Total length: 195,5 mm
Item no.:357003
  • Position: Outer
  • Inner splines: 22
  • Seal diameter: 51 mm
  • Outer splines: 25
  • Thread size: M24X1,5
Item no.:0643330
  • Outer diameter: 22 mm
  • Diameter: 78 mm
Item no.:148973
  • Position: Inner
  • Inner splines: 22
  • Splines gearbox side: 22
  • Total length: 159 mm
Item no.:245607
  • Position: Inner
  • Splines gearbox side: 22
  • Splines wheel side: 22
  • Total length: 196 mm
  • ABS teeth: 22
Item no.:0632196
  • Outer diameter: 19 mm
  • Diameter: 76 mm
Item no.:159778
  • Position: Outer
  • Inner splines: 22
  • Seal diameter: 51 mm
  • Outer splines: 22
  • Thread size: M22X1,5

Drivetrain for Peugeot Bipper

The Peugeot Bipper is a compact and nimble commercial van that places tough demands on its drivetrain, particularly when driven in stop-start urban traffic. The drivetrain is the critical chain of components transferring engine power to the wheels, and for a front-wheel-drive vehicle like the Bipper, this means every single component must be in top condition to sustain fuel economy and driveability. As specialists in drivetrain components, we offer solutions tailored to withstand the specific stresses this model encounters in daily commercial use.

Maintaining the drivetrain on your Peugeot Bipper is not merely a matter of comfort, but also of safety and running costs. A properly functioning power transfer reduces wear on surrounding mechanical assemblies and ensures the vehicle behaves predictably in every driving situation. We supply car parts that match or exceed original equipment specifications, giving you complete confidence that your van will remain reliable for a long time to come.

How the Peugeot Bipper drivetrain is designed

The drivetrain in a Peugeot Bipper is built with a focus on space efficiency and durability. It primarily consists of a transverse engine mated to a gearbox, which in turn powers the front wheels via two drive shafts. Each driveshaft is fitted with two joints: an inner CV joint located closest to the gearbox and an outer CV joint situated at the wheel hub. This layout enables the front wheels to steer and propel the van simultaneously, requiring high precision in the articulation of every component.

The outer CV joints are particularly vital, as they must handle significant angular changes on full steering lock. To protect these sensitive components, flexible rubber CV boots are fitted to retain grease and keep out dirt and moisture. If a CV boot tears, the joint is directly exposed to grit and road grime, rapidly causing wear. Understanding this assembly highlights why routine inspection of your drivetrain components is essential for the Peugeot Bipper.

Common faults and symptoms

There are several distinct signs indicating that the drivetrain on your Peugeot Bipper is wearing out. One of the most common symptoms is a clicking or knocking noise when turning tightly, which usually points to a failing outer constant velocity joint on your Peugeot Bipper. If the knocking or clunking instead occurs under straight-line acceleration, an inner joint or the drive shaft itself may be the culprit. Vibrations through the steering wheel or chassis under load are further warning signs that should never be ignored.

Another frequent issue is grease leaking from split CV boots. If you spot grease splattered on the inside of the wheel rim or underneath where you park, it is time to inspect the drivetrain immediately. Caught early, fitting a replacement boot may suffice, but if road dirt has already penetrated the constant velocity joint, a full replacement is typically required. Ignoring these warnings can lead to total breakdown, leaving your van stranded and resulting in a much more expensive repair than replacing the worn part promptly.

Common Peugeot Bipper parts to replace

For the Peugeot Bipper, drive shafts and outer CV joints are the parts most frequently replaced over the vehicle's working life. We have tailored our range to address the most common requirements for this model. Here are the most relevant categories for your vehicle:

  • Drive shafts for Peugeot Bipper – We stock a variety of options covering different engine variants and model years.
  • Outer CV joints for Peugeot Bipper – We provide specific units engineered for a precise fit at the wheel hub.

Alongside these main assemblies, CV boots and ABS rings often require replacement. Because the Peugeot Bipper is regularly used as a work van, these components face demanding environments where material fatigue can occur sooner than on standard passenger cars. Selecting the right spare parts from the start ensures your Bipper maintains its payload capacity and dependability without unplanned downtime.

How to find the right part for your Peugeot Bipper

Navigate directly to the appropriate section for your Peugeot Bipper:

On a vehicle with several potential drivetrain issues, it pays to start directly in the correct category. Comparing the exact component sections for the Peugeot Bipper makes it straightforward to distinguish between faults in a drive shaft, CV joint or propeller shaft, taking you directly to the page that best matches your symptoms and fitment needs.

Finding the correct replacement for your Peugeot Bipper is straightforward. Because technical specifications vary according to engine size, gearbox type and production year, we recommend selecting your exact make, model and engine from our vehicle selector. This filters our catalogue directly to items verified for your specific van, providing the most reliable way to avoid ordering errors and ensure your new component matches original dimensions.

Once your results appear, you can check technical details such as the tooth count on the ABS reluctor ring or the overall drive shaft length if you want to be completely certain. Our catalogue is designed to give you total confidence in your choice. If you are ever unsure, our specialist team is on hand to guide you through our comprehensive range of drivetrain components. We aim to make your purchase smooth and accurate from search to delivery.

Why shop at CVJoint24

CVJoint24 is the international shop of a Swedish driveline specialist shipping from our warehouse in Helsingborg, Sweden, across the EU, with a reputation built on technical know-how and premium product quality. When ordering parts for your Peugeot Bipper from us, you receive dependable spare parts backed by an expert understanding of your vehicle's power transmission requirements. We maintain extensive stock to ensure fast dispatch and high availability, which is essential when you need your commercial vehicle back on the road without delay.

Our specialist focus provides an inventory depth that general car parts retailers rarely match. We know exactly what is required for a Peugeot Bipper drive shaft to perform reliably on demanding European roads. Combining accurate fitment, durable materials and a dedicated customer support team who know drivetrains inside out, we are the trusted choice for both private owners and professional garages who expect the best for their Peugeot.

Frequently Asked Questions about Drivetrain Parts for Peugeot Bipper

How many drive shafts do you stock for Peugeot Bipper?

We currently stock 6 different drive shafts matched for Peugeot Bipper to cover various specifications and model variants.

What are the most common signs of a failing CV joint on a Bipper?

The most common symptoms are a clicking noise on full lock, vibrations during acceleration, or visible grease leaks from a damaged CV boot.

How do I make sure I find the right parts for my car?

We recommend selecting your Peugeot Bipper's exact model and engine variant in our search filter to ensure you receive parts with a precise fit.

Do you sell outer CV joints separately for Peugeot Bipper?

Yes, we have 2 specific outer CV joints in our range tailored for Peugeot Bipper.

Why should I choose CVJoint24 for my spare parts?

We are Swedish driveline specialists focusing on high quality, accurate fitment and in-depth technical knowledge of the Peugeot Bipper.

Is it difficult to replace a drive shaft on a Peugeot Bipper yourself?

It requires some mechanical experience and the right tools, but because our parts are tailored for an exact fit, the job is significantly easier than with universal components.