Skoda Enyaq IV Coupé 80X 4X4

Spare parts and drivetrain components for the Skoda Enyaq IV Coupé 80X 4X4. Confirm fitment by selecting your make, model and engine before ordering.

Products for Skoda Enyaq IV Coupé 80X 4X4

10 products
1 - 10 of 10
Item no.:1126121
  • Position: Front left
  • Splines gearbox side: 33
  • Splines wheel side: 38
  • Total length: 663 mm
Item no.:1151198
  • Position: Front left
  • Splines gearbox side: 33
  • Splines wheel side: 38
  • Total length: 565 mm
Item no.:2160697
  • Position: Front right
  • Splines gearbox side: 33
  • Splines wheel side: 38
  • Total length: 721 mm
Item no.:0559263
  • Position: Outer
Item no.:2177499
  • Position: Front right
  • Splines gearbox side: 33
  • Splines wheel side: 38
  • Total length: 622 mm
Item no.:4179548
  • Position: Rear left
  • Splines gearbox side: 37
  • Splines wheel side: 38
  • Total length: 634 mm
Item no.:5184431
  • Position: Rear right
  • Splines gearbox side: 37
  • Splines wheel side: 38
  • Total length: 859 mm
Item no.:344544
  • Position: Front, Inner
  • Inner splines: 32
  • Splines gearbox side: 33
  • Seal diameter: 39,9 mm
  • Total length: 163,5 mm
Item no.:0530724
  • Position: Outer
  • Inner splines: 28
  • Seal diameter: 59,5 mm
  • Outer splines: 38
  • Total length: 115 mm
Item no.:1128712
  • Position: Front left
  • Splines gearbox side: 33
  • Splines wheel side: 38
  • Total length: 633 mm

Drivetrain for Skoda Enyaq IV Coupé 80X 4X4

Owning a Skoda Enyaq IV Coupé 80X 4X4 means you are driving one of the most advanced electric drivetrains on the market today. This specific model features all-wheel drive, distributing power from the high-voltage battery to both the front and rear axles via two separate electric motors. For this power transfer to operate seamlessly and efficiently, top-tier components are essential. At CVJoint24, you will find specialised parts engineered to withstand the unique stresses imposed by a heavy electric vehicle delivering instant high torque. We focus on providing parts that match original factory specifications, ensuring your Skoda Enyaq IV Coupé continues to deliver the silent, powerful driving experience you expect.

Our range for the 80X 4X4 model is comprehensive and specific, allowing us to supply precise solutions where others fall short. Whether you require a complete drive shaft or a specific outer CV joint, you can trust that our products are rigorously tested to withstand demanding European road conditions and the high loads of modern electric vehicles. By selecting the correct parts from the start, you minimise the risk of secondary damage and ensure that advanced vehicle safety systems, such as traction control and electronic stability control, function in perfect harmony with the mechanical drivetrain.

How the drivetrain is engineered on the Skoda Enyaq IV Coupé 80X 4X4

The drivetrain in a Skoda Enyaq IV Coupé 80X 4X4 differs significantly from conventional combustion-engine cars. Rather than relying on a central propeller shaft running along the underside of the floorpan, the 80X setup uses an electric motor on each axle—an arrangement often known as an "e-AWD" system. The front motor drives the front wheels through a compact single-speed reduction gearbox and two drive shafts, while the rear motor powers the rear wheels. This configuration delivers exceptionally fast throttle response and enables precise torque vectoring to each wheel, which is vital for both road grip and energy efficiency.

Because electric motors generate their full torque from zero rpm, the drive shafts and constant velocity joints are subjected to significantly higher torque spikes than those in a petrol or diesel car. Every drive shaft for the Skoda Enyaq IV Coupé 80X 4X4 must therefore be manufactured with extreme precision and high-grade materials to prevent torsional flexing or premature wear. The CV joints, both inner and outer, play a critical role in accommodating suspension travel and steering articulation while transferring this enormous power smoothly and without vibration. Understanding this engineering layout is key to choosing the correct replacement parts during maintenance or repairs.

Common faults and symptoms

Although electric vehicles generally feature fewer moving parts than traditional vehicles, the mechanical drivetrain remains subject to normal wear and tear. One of the most typical signs that something is wrong with your Skoda is a clicking or knocking noise when turning sharply at low speeds. This is a classic symptom of a worn outer CV joint on the Skoda Enyaq IV Coupé 80X 4X4. If left unaddressed, the joint can eventually fail completely, resulting in a sudden loss of drive to that wheel.

Another common symptom is vibration felt through the car's chassis under acceleration. This is often attributable to worn inner CV joints or an imbalance in the driveshaft itself. Because the Enyaq is exceptionally quiet inside the cabin, mechanical noises often become much more noticeable than in combustion cars. It is equally important to inspect the CV boots regularly for leaking grease. A split or torn boot is the most frequent cause of CV joint failure, as it allows road dirt and moisture to enter while flinging out the vital lubricating grease. Catching a cracked boot early can save significant expense by preventing the need for a full drive shaft replacement.

Common parts to replace on the Skoda Enyaq IV Coupé 80X 4X4

For the Skoda Enyaq IV Coupé 80X 4X4, drive shafts and outer CV joints are the primary wear items requiring attention during drivetrain servicing. Our data shows that the combination of permanent four-wheel drive and a substantial kerb weight places specific wear demands on these components over time. We stock parts tailored specifically for this model variant, covering multiple driveshaft configurations across front and rear axles as well as different production batches.

  • Drive shafts: Complete assemblies including both inner and outer CV joints, fully assembled and ready for direct bolt-on installation.
  • Outer CV joints: The wheel-side joint that accommodates steering angles while transmitting drive power.
  • CV boots: Durable rubber or thermoplastic gaiters that retain lubricating grease and seal out abrasive dirt and water.

Replacing an entire drive shaft is often more time-efficient and provides long-term peace of mind, as you gain brand-new joints at both ends. For those carrying out targeted repairs, replacing a worn outer CV joint independently remains a practical option. Whichever route you take, ensuring the part is precisely matched to the 80X model specifications is crucial, as an improper fit can cause costly damage to the electric drive units or wheel bearings.

How to find the right part for your Skoda Enyaq IV Coupé 80X 4X4

Navigate directly to the relevant component section for your Skoda Enyaq IV Coupé 80X 4X4:

When troubleshooting potential driveline issues, selecting the correct category from the start is essential. By comparing the dedicated part categories for the Skoda Enyaq IV Coupé 80X 4X4, it is easy to distinguish between drive shaft, CV joint, or prop shaft faults and proceed to the exact section matching your symptoms and technical specifications.

Once you are in the correct category, always verify whether the component is intended for the front or rear axle, and note whether it fits the left or right-hand side. On the 80X model, this distinction is particularly critical because the front and rear drive shafts have different dimensions and torque ratings. If you are unsure which part matches your exact model year or equipment trim, please contact our customer support team. As driveline specialists, we are always on hand to help you find the correct component first time.

Why shop with CVJoint24

CVJoint24 is not just another general car parts retailer; we are the international shop of a Swedish driveline specialist, supplying high-quality transmission and driveline components directly from our central warehouse in Helsingborg, Sweden. Our technical expertise in this field allows us to combine comprehensive catalogue knowledge with rigorously tested product quality. When you source parts for your Skoda Enyaq IV Coupé 80X 4X4 from us, you receive dependable components designed to fit accurately and deliver long service life. We understand the precise technical demands of modern electric vehicles and select our manufacturing partners with great care.

We dispatch orders promptly across the European Union, understanding how vital it is to get your vehicle back on the road without delay. By choosing your car's make, model, and engine variant in our store, you can order with total confidence. We maintain well-stocked shelves at competitive prices without ever compromising on component quality. As a customer, you benefit from our dedicated focus on driveline technology, making CVJoint24 your ideal specialist partner for all your power transmission needs. Welcome to a driveline specialist that truly understands your vehicle's mechanical engineering.

Frequently asked questions about the drivetrain for Skoda Enyaq IV Coupé 80X 4X4

How do I know if my Skoda Enyaq 80X needs a new drive shaft?

The most common signs are vibrations under acceleration or unusual noises from the drivetrain. As the 80X is four-wheel drive, the issue can occur on either the front or rear axle. Check the CV boots for splits or grease leaks, as this often precedes complete drive shaft failure.

Do drive shafts from the rear-wheel-drive Enyaq 80 fit my 80X 4X4?

No, the 80X 4X4 features a unique drivetrain configuration with an additional front motor, meaning the front drive shafts are specific to all-wheel-drive models. Always select your car's make, model and engine to ensure the correct fitment.

Why is there a clicking noise when I turn in my Enyaq IV Coupé?

A clicking noise on full steering lock is a classic symptom of a worn outer CV joint. The high, instantaneous torque of electric motors can accelerate wear if a CV boot has split and allowed dirt to enter the joint.

Is it difficult to replace a CV joint on an electric car like the Enyaq?

The mechanical replacement itself is similar to conventional cars, but you must take extra care around the vehicle's high-voltage system and sensitive sensors. We recommend having the work carried out by an experienced DIY mechanic or a professional garage.

Are the CV boot and grease included when I buy an outer CV joint from you?

Yes, our outer CV joints are supplied as complete kits including the CV joint, CV boot, specialist grease and necessary fitting hardware such as circlips and bolts to ensure a correct installation.

How does a damaged drive shaft affect the car's driving range?

A damaged or binding constant velocity joint creates extra friction, which in theory can negatively impact energy efficiency and range. Furthermore, vibrations from a worn driveshaft can cause unnecessary wear to motor bearings and other drivetrain components.