Audi 80 2.6

Car parts and drivetrain components for Audi 80 2.6. Always check the fit before ordering.

Products for Audi 80 2.6

12 products
1 - 12 of 12
Item no.:1111829
  • Position: Front left
  • Flange diameter: 130 mm
  • Total length: 572 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:2121901
  • Position: Front right
  • Flange diameter: 130 mm
  • Total length: 550 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:0302458
  • ABS teeth: 45
  • Inner diameter: 64 mm
  • Outer diameter: 74 mm
  • Width: 8,1 mm
Item no.:0574610
  • Position: Outer
  • ABS teeth: 45
  • Seal diameter: 59 mm
  • Inner splines: 27
  • Outer splines: 38
Item no.:339419
  • Position: Front
  • ABS teeth: 45
  • Inner diameter: 64 mm
  • Outer diameter: 74 mm
  • Width: 8,1 mm
Item no.:0626476
  • Position: Front
  • Diameter: 91 mm
  • Outer diameter: 24 mm
Item no.:0474051
  • Position: Inner
  • Seal diameter: 94 mm
  • Inner splines: 33
  • Number of joints: 3
  • ABS teeth: 0
Item no.:215764
  • Total length: 559 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:210572
  • Total length: 524 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:119156
  • Total length: 475 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:2114502
  • Position: Front right
  • Flange diameter: 130 mm
  • Total length: 550 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:0668591
  • Inner diameter: 24 mm
  • Total length: 92 mm

Frequently Asked Questions about Drivetrain for Audi 80 2.6

How do I know if my Audi 80 2.6 needs a new drive shaft?

The most common symptoms are vibrations through the car under acceleration or noises when driving in a straight line. If the vibrations stop when you lift off the accelerator, it is often a worn inner joint or the drive shaft itself.

Does the same CV joint fit all Audi 80 models?

No, the Audi 80 2.6 often uses sturdier CV joints and shafts than the smaller engine variants to handle the higher torque of the V6 engine. Always select your car's make, model and engine to find the correct version.

Why does the ABS ring crack on the Audi 80 2.6?

This is usually caused by corrosion developing underneath the ring on the CV joint. The rust expands and creates pressure from within, which eventually causes the hardened steel ring to crack, triggering false signals to the ABS sensor.

Can I replace just the ABS ring or do I need to replace the entire CV joint?

If the CV joint is otherwise in good condition and makes no unusual noises, you can easily replace just the ABS ring. It is a cost-effective way to extinguish the ABS warning light.

What is included in a CV joint kit for the Audi 80 2.6?

Our kits typically include the outer CV joint, a vehicle-specific CV boot, high-quality grease, circlips, a bolt or nut, and clamps for the boot.

How quickly do you deliver parts for the Audi 80 2.6?

We offer fast delivery on most of our stocked products, helping you get your car repaired and back on the road in no time.