Audi A3 2.0 TDI 16V Quattro

Spare parts and drivetrain components for the Audi A3 2.0 TDI 16V Quattro. Check compatibility using your vehicle details before ordering.

Products for Audi A3 2.0 TDI 16V Quattro

50 products
1 - 24 of 50
Item no.:0252956
  • Inner diameter: 30 mm
  • Bearing thickness: 13 mm
  • Hole spacing c/c: 188 mm
Item no.:0455836
  • Position: Inner
  • Inner splines: 28
  • Seal diameter: 108 mm
  • Total length: 32 mm
  • Joint diameter: 108 mm
Item no.:0423292
  • Position: Inner
  • Inner splines: 33
  • Seal diameter: 100 mm
  • Total length: 34 mm
  • Joint diameter: 100 mm
Item no.:0519653
  • Position: Outer
  • Inner splines: 30
  • Splines wheel side: 36
  • Seal diameter: 60 mm
  • Outer splines: 36
Item no.:0514223
  • Position: Outer
  • Inner splines: 27
  • Seal diameter: 59 mm
  • Outer splines: 36
  • Thread size: M16X1,5
Item no.:0202623
  • Total length: 2,222 mm
  • Number of joints: 1
  • Number of centre bearings: 1
Item no.:0181107
  • Position: Front right
  • Splines gearbox side: 37
  • Total length: 484 mm
Item no.:1187344
  • Position: Front left
  • Splines wheel side: 36
  • Total length: 495 mm
  • Joint diameter: 98 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:2103820
  • Position: Front right
  • Splines wheel side: 36
  • Total length: 600 mm
  • Joint diameter: 98 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:4193217
  • Position: Rear left
  • Splines wheel side: 36
  • Total length: 594 mm
  • Diameter 2: 100 mm
  • Flange diameter: 100 mm
Item no.:5150063
  • Position: Rear right
  • Splines wheel side: 36
  • Total length: 631 mm
  • Diameter 2: 100 mm
  • Flange diameter: 100 mm
Item no.:1286210
  • Position: Front left
  • Splines gearbox side: 28
  • Splines wheel side: 27
  • Total length: 405 mm
Item no.:648126
  • Position: Rear, Inner
  • Splines gearbox side: 33
  • Outer splines: 33
  • Diameter: 86 mm
  • Width: 34 mm
Item no.:659558
  • Position: Rear, Outer
  • Inner splines: 33
  • Seal diameter: 59 mm
  • Outer splines: 36
  • Joint diameter: 82 mm
Item no.:657057
  • Position: Rear, Outer
  • Inner splines: 33
  • Seal diameter: 59,5 mm
  • Total length: 80 mm
  • Splines gearbox side: 36
Item no.:213858
  • Position: Front right
  • Splines wheel side: 36
  • Total length: 795 mm
  • Joint diameter: 98 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:348338
  • Position: Inner
  • Inner splines: 32
  • Seal diameter: 31 mm
  • Total length: 153,5 mm
  • Joint diameter: 82 mm
Item no.:343581
  • Position: Front right, Inner
  • Inner splines: 28
  • Seal diameter: 50 mm
  • Total length: 300 mm
  • Joint diameter: 102 mm
Item no.:628877
  • Position: Rear
  • Total length: 2,223 mm
  • Number of joints: 1
Item no.:341250
  • Position: Inner
  • Inner splines: 28
  • Seal diameter: 46 mm
  • Total length: 136,2 mm
  • Joint diameter: 98 mm
Item no.:1181104
  • Position: Front left
  • Splines wheel side: 36
  • Total length: 480 mm
  • Joint diameter: 110 mm
  • ABS teeth: 28
Item no.:621551
  • Position: Rear
  • Total length: 2,170 mm
  • Number of joints: 1
  • Outer diameter 1: 16 mm
  • Bolt circle diameter 1: 96 mm
Showing 1–24 of 50 products

Audi A3 2.0 TDI 16V Quattro drivetrain parts

Owning an Audi A3 2.0 TDI 16V Quattro means driving a car with an advanced four-wheel drive system that demands the highest quality components to maintain its performance and safety. The drivetrain in this specific model is engineered to handle the substantial torque produced by the 2.0 TDI engine, while the Quattro system distributes power efficiently between the front and rear wheels. At CVJoint24, you will find a curated range of specific parts tailored precisely to this vehicle setup. We understand the importance of every part in the chain—from the gearbox to the wheel hub—working in seamless harmony to prevent unnecessary wear on costly components such as the Haldex coupling or differential.

Our focus is on supplying components that not only fit physically, but also meet the stringent technical tolerances and material strengths specified by Audi. By choosing the right spare parts for your Audi A3, you ensure that the car's driving characteristics remain intact, whether for your daily commute or driving in demanding winter conditions. As a Swedish driveline specialist shipping from our central warehouse in Helsingborg, we bring deep technical knowledge of how these four-wheel drive systems are built and how they withstand harsh road conditions across Europe.

How the drivetrain is engineered on the Audi A3 2.0 TDI 16V Quattro

The drivetrain on an Audi A3 2.0 TDI 16V Quattro is a sophisticated assembly that differs considerably from front-wheel-drive configurations. Power from the transverse diesel engine passes first through the gearbox to an angle drive. From here, power is transferred partly to the front wheels via the front drive shafts, and partly backwards via a propeller shaft to the rear differential. Here lies the core of the Quattro system, typically an electronically controlled multi-plate clutch that instantly regulates how much torque is directed to the rear wheels depending on road grip and driving dynamics.

This setup places high demands on all driveline components. The front drive shafts must cope with both steering angles and drive torque, while the rear shafts and prop shaft must be precisely balanced to eliminate vibrations. Because the entire system is mechanically linked, a fault in one component—such as a worn inner constant velocity joint—can cause vibrations that travel through the chassis and potentially damage bearings inside the gearbox or differential. Understanding this complexity is vital when selecting the correct spare parts whenever work is needed on your car's drivetrain.

Common faults and symptoms

There are several telltale signs that driveline parts on your Audi A3 2.0 TDI 16V Quattro are wearing out. One of the most common symptoms is a clicking or knocking sound on full steering lock, which almost always indicates a worn outer CV joint. If you experience chassis vibration during acceleration instead, particularly at higher road speeds, a worn inner CV joint or an imbalanced propeller shaft is usually the culprit. Because Quattro models have more moving driveline parts than standard two-wheel-drive variants, paying attention to these early warning signs is especially crucial.

Another critical area to monitor is the condition of the CV boots. If a drive shaft boot splits or tears, the lubricating grease escapes while road grit and water penetrate, rapidly destroying the joint. On four-wheel-drive vehicles, imbalance in the prop shaft or a failed centre bearing can also produce a low humming or droning noise that intensifies with vehicle speed. Inspecting these parts regularly and taking swift action at the first sign of wear protects against expensive damage to the rest of the transmission. We always recommend thoroughly checking all rubber gaiters during routine servicing to prevent breakdown.

Common parts to replace on the Audi A3 2.0 TDI 16V Quattro

When repairs are due, we make it simple to find the precise parts you need. For the Audi A3 2.0 TDI 16V Quattro, we supply a comprehensive range covering the most frequent maintenance requirements to restore smooth, dependable operation. Here are the most sought-after categories for your car:

  • Drive shafts for Audi A3 2.0 TDI 16V Quattro – We stock several variants to cover all fitting positions and technical specifications.
  • Outer CV joints for Audi A3 2.0 TDI 16V Quattro – 3 high-quality options to resolve knocking or clicking noises while turning.
  • Inner CV joints for Audi A3 2.0 TDI 16V Quattro – 3 precision-engineered parts designed to eliminate shudder and vibration under acceleration.
  • Propeller shafts for Audi A3 2.0 TDI 16V Quattro – 3 robust replacements engineered for smooth, vibration-free power delivery to the rear axle.

By replacing worn assemblies with our vehicle-specific parts, you can count on exact original-equipment fitment. This saves time in the workshop and ensures your car performs reliably for many thousands of kilometres to come.

How to find the right part for your Audi A3 2.0 TDI 16V Quattro

Browse directly to the relevant category for your Audi A3 2.0 TDI 16V Quattro:

On a vehicle with several interdependent drivetrain components, starting in the right subcategory saves valuable time. By comparing the exact sections for the Audi A3 2.0 TDI 16V Quattro, it is straightforward to distinguish between symptoms caused by a drive shaft, a CV joint or the propeller shaft, guiding you to the right replacement part for your car.

Identifying the exact part for your Audi A3 2.0 TDI 16V Quattro can sometimes be tricky, as variations exist according to production date or specific chassis numbers. To make the process straightforward and reliable, simply select your car's make, model, year and engine variant in our store selector. Our catalogue filters automatically to display only the parts engineered for your exact specification, removing guesswork and ensuring your replacement parts fit first time.

If you are ever unsure, our specialist team is on hand to assist you. We possess comprehensive technical expertise in drive shafts, constant velocity joints and prop shafts, and can help you determine the right component for your vehicle's symptoms. Our aim is to ensure you order correctly right from the start, saving both time and money. With our fitment guarantee, you can order with complete confidence, knowing our parts are thoroughly checked for compatibility with your Audi.

Why buy from CVJoint24?

CVJoint24 is not just a generic car parts seller; we are a dedicated Swedish driveline specialist focused exclusively on driveshafts, CV joints and power transmission components. When you order from us, you benefit from focused technical knowledge that general retailers rarely offer. We understand the engineering behind the Audi A3 2.0 TDI 16V Quattro and curate our stock to meet the highest demands for durability, performance and longevity. Our business is built on supplying the right component, promptly and at a competitive price.

Dispatched swiftly from our Swedish central warehouse across the European Union, our components minimise downtime in the garage. We know that when a drive shaft or prop shaft fails, you need a dependable replacement quickly to get your vehicle back on the road. Benefit from specialist driveline expertise and dependable European delivery—choose CVJoint24 for quality parts you can trust.

Frequently asked questions about the drivetrain for Audi A3 2.0 TDI 16V Quattro

How do I know if my Audi A3 Quattro needs a new drive shaft?

The most common signs are vibrations under acceleration or clicking noises when turning. If you notice a split CV boot and grease has leaked out, there is a high risk that the shaft or joint will need replacing shortly.

What is the difference between the inner and outer CV joint on an A3 2.0 TDI?

The outer CV joint is located at the wheel and handles steering angles; it typically makes clicking noises when cornering. The inner CV joint sits by the gearbox and absorbs suspension movement; wear here usually causes vibrations throughout the car under acceleration.

Why does my Audi A3 vibrate under acceleration?

On a Quattro model, vibrations under acceleration are often caused by worn inner CV joints or an imbalance in the propeller shaft. Because the 2.0 TDI engine delivers high torque, these components are placed under significant strain.

Do all propeller shafts fit the Audi A3 2.0 TDI 16V Quattro?

No, the propeller shaft is specific to Quattro models and can vary depending on gearbox type and model year. Always select your car's make, model and engine to find the exact prop shaft for your vehicle.

How does the fitment guarantee work at CVJoint24?

When you select your car's make, model and engine and choose a part recommended for your vehicle, we guarantee that it will fit. If it turns out not to fit against all expectations, we will help you find the correct part without any hassle.

Can I replace just the CV boot instead of the entire CV joint?

Yes, if you catch the damage early before dirt and moisture have entered to ruin the bearing surfaces inside the joint, replacing the CV boot and repacking it with fresh grease may suffice. However, if the joint has already started making noise, it must be replaced.