Audi A4 1.8 T Quattro

Spare parts and drivetrain components for Audi A4 1.8 T Quattro. Check fitment by vehicle make, model and engine before ordering.

Products for Audi A4 1.8 T Quattro

60 products
1 - 24 of 60
Item no.:0355845
  • ABS teeth: 45
  • Inner diameter: 77 mm
  • Outer diameter: 81 mm
  • Width: 11 mm
Item no.:0261294
  • Position: Inner
  • Inner splines: 25
  • Joint diameter: 100 mm
Item no.:332603
  • Position: Front
  • ABS teeth: 45
  • Inner diameter: 77 mm
  • Outer diameter: 81 mm
  • Width: 11 mm
Item no.:2153359
  • Position: Front right
  • Flange diameter: 123 mm
  • Total length: 620 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:0292325
  • Diameter: 30 mm
  • Height: 85 mm
  • Hole spacing c/c: 228 mm
  • Bearing thickness: 15 mm
Item no.:1178116
  • Position: Front left
  • Flange diameter: 123 mm
  • Total length: 595 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:3178271
  • Position: Front left, Front right
  • Flange diameter: 123 mm
  • Joint diameter: 123 mm
  • Total length: 544 mm
  • ABS teeth: 45
Item no.:3151721
  • Position: Front left, Front right
  • Flange diameter: 123 mm
  • Total length: 521 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:0468172
  • Position: Inner
  • Seal diameter: 123 mm
  • Inner splines: 34
Item no.:0576072
  • Position: Outer
  • ABS teeth: 45
  • Seal diameter: 59 mm
  • Inner splines: 33
  • Outer splines: 38
Item no.:616173
  • Position: Rear
  • Total length: 612 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:0418380
  • Position: Inner
  • Seal diameter: 130 mm
  • Inner splines: 34
Item no.:0257896
  • Number of centre bearings: 1
  • Number of joints: 3
  • Total length: 1,565 mm
Item no.:0468562
  • Position: Inner
  • Seal diameter: 100 mm
  • Inner splines: 33
  • Joint diameter: 100 mm
Item no.:0566194
  • Position: Outer
  • ABS teeth: 45
  • Seal diameter: 53 mm
  • Inner splines: 30
  • Outer splines: 33
Item no.:0556500
  • Position: Outer
  • ABS teeth: 45
  • Seal diameter: 53 mm
  • Inner splines: 30
  • Outer splines: 33
Item no.:0894126
  • Inner diameter: 30 mm
Item no.:317893
  • Outer diameter: 100 mm
Item no.:621377
  • Position: Rear
  • Total length: 1,149 mm
Item no.:2127107
  • Position: Front right
  • Flange diameter: 123 mm
  • Total length: 490 mm
  • Splines wheel side: 38
  • ABS teeth: 45
Item no.:1122818
  • Position: Front left
  • Flange diameter: 130 mm
  • Total length: 495 mm
  • Splines wheel side: 33
  • ABS teeth: 45
Item no.:1112221
  • Position: Front left
  • Flange diameter: 100 mm
  • Total length: 615 mm
  • Splines wheel side: 33
  • ABS teeth: 45
Item no.:2100856
  • Position: Front right
  • Flange diameter: 130 mm
  • Total length: 585 mm
  • Splines wheel side: 33
  • ABS teeth: 45
Item no.:2116380
  • Position: Front right
  • Flange diameter: 100 mm
  • Total length: 636 mm
  • Splines wheel side: 33
  • ABS teeth: 45
Showing 1–24 of 60 products

Drivetrain for Audi A4 1.8 T Quattro

The Audi A4 1.8 T Quattro represents a fine balance of German engineering and everyday usability, where a lively turbocharged engine meets the superior traction of the Quattro all-wheel-drive system. To maintain this balance, it is vital that every part of the drivetrain operates smoothly. On this page, we have gathered a comprehensive range of car parts tailored specifically to this model variant. With a total of 33 carefully selected products in our range, we provide solutions for virtually every power-transmission requirement. The drivetrain in a four-wheel-drive car such as the Audi A4 1.8 T Quattro handles far greater stresses than its two-wheel-drive counterpart, as engine torque is distributed across all four wheels rather than just two. This places stricter demands on materials and manufacturing tolerances for drive shafts, constant velocity joints and propeller shafts. At CVJoint24, we specialise specifically in these driveline components to offer you the highest standard of quality and expertise. Choosing the right parts safeguards not only your car's performance, but also its long-term reliability and resale value.

How the Audi A4 1.8 T Quattro drivetrain is designed

The mechanical layout of the Audi A4 1.8 T Quattro drivetrain is a masterclass in efficient power delivery. The engine is mounted longitudinally, typical of larger Audi models, allowing for a balanced, symmetrical drivetrain layout. Power transfers from the manual or automatic gearbox to a centre differential—typically a mechanical Torsen unit—which immediately directs torque to the axle with the best traction. The front axle is driven by two drive shafts equipped with both inner and outer CV joints to accommodate steering angle and suspension movement. The rear axle receives drive via a robust propeller shaft running down the central tunnel to a rear differential, which then splits power to the rear wheels through another pair of driveshafts. This entire mechanical setup works alongside the electronic stability control and ABS system, where ABS rings on every hub feed vital wheel-speed data. Every link in this chain must stay in peak condition for the Quattro system to deliver the dependable traction and composure for which Audi is renowned.

Common faults and symptoms

Spotting drivetrain issues on an Audi A4 1.8 T Quattro requires both attention and a bit of mechanical know-how. One of the most typical signs of wear is a rhythmic clicking sound from an outer CV joint on full lock, such as when parking or turning tightly at a junction. If you notice a low-frequency vibration felt through the floorpan under acceleration instead, the culprit is often worn inner CV joints or play in the prop shaft centre bearing and universal joints. Because the 1.8 T engine produces solid torque from low revs, inner joints endure high loads that can create noticeable play over time. Another frequent issue is a cracked or heavily corroded ABS ring caused by road grit and salt, leading to unprompted ABS pulsing under braking or an illuminated warning light. Always check for split or leaking CV boots as well; once grease escapes from a drive shaft boot, dirt quickly enters and ruins the joint. Ignoring these symptoms can lead to expensive damage to the differentials or leave you stranded at the roadside.

Common replacement parts for Audi A4 1.8 T Quattro

When maintaining or repairing your Audi A4 1.8 T Quattro, using components built to lasting standards is essential. Our range is tailored to cover the most frequent service needs for this model. Here are the most sought-after categories for your car:

  • Drive shafts for Audi A4 1.8 T Quattro - We offer 18 different variants for both front and rear axles.
  • Outer CV joints for Audi A4 1.8 T Quattro - 5 options to eliminate clicking noises on turns.
  • Inner CV joints for Audi A4 1.8 T Quattro - 5 versions to stop acceleration vibrations.
  • Propeller shafts for Audi A4 1.8 T Quattro - A central component to restore your all-wheel-drive system.
  • ABS rings for Audi A4 1.8 T Quattro - 3 options to fix erratic ABS issues.

Replacing worn components with our precision spare parts restores your car's original driving dynamics, ensuring smooth, efficient power transmission in all driving conditions. Every component is chosen for durability and an accurate fit against Audi's original specifications.

How to find the right part for your Audi A4 1.8 T Quattro

Navigate directly to the appropriate section for the Audi A4 1.8 T Quattro:

When troubleshooting multiple possible drivetrain issues, starting in the correct category saves time. By comparing the exact sections for the Audi A4 1.8 T Quattro, it is straightforward to differentiate between problems with a drive shaft, CV joint or propeller shaft, and head straight to the page matching your symptoms and specifications.

To help you order the correct component with confidence, we provide tools that streamline your selection. The most reliable method to source parts for your Audi A4 1.8 T Quattro is to select your vehicle make, model and engine variant in our store selector. This quickly filters out the 33 parts verified for your car. Please bear in mind that Audi introduced production changes over the years that may not be fully identifiable by the chassis code alone. We therefore recommend verifying key dimensions—such as the spline count on the CV joint or the diameter of the ABS reluctor ring—against the part currently on your car. To view a wider selection of components or parts for related models, feel free to browse our main Audi A4 category. We want you to get the correct part first time, and our team is always on hand to assist with technical questions if you need help confirming fitment for your model year.

Why buy from CVJoint24

Choosing CVJoint24 means relying on an international shop backed by a Swedish driveline specialist, focused exclusively on drivetrain and transmission components. We are not a general motor factor; we specialise in this field. This dedicated focus allows us to maintain exceptional quality standards and keep hard-to-find components for the Audi A4 1.8 T Quattro in stock. We provide a dependable fitment guarantee so you can shop with peace of mind. Select your exact vehicle specification in our shop, and we ensure the recommended part matches your car. With fast dispatched orders shipped from our central Swedish warehouse across the EU, you get your components quickly, minimising workshop downtime and getting you back on the road. We aim to supply the right parts at competitive prices, without cutting corners on durability. Turn to a specialist who understands your vehicle and is committed to delivering reliable drivetrain solutions.

Frequently Asked Questions about Drivetrain for Audi A4 1.8 T Quattro

How do I know if the CV joint is failing on my Audi A4 1.8 T Quattro?

The most common symptom is a clicking noise from the front suspension when making sharp turns under acceleration. If you experience vibrations during straight-line acceleration, it may indicate that the inner CV joints are worn instead.

Do all Audi A4 drive shafts fit the 1.8 T Quattro model?

No, Quattro models often use distinct drive shafts at both the front and rear to accommodate the all-wheel-drive system. Always select your vehicle's make, model, and engine variant to guarantee the correct fitment.

Why does my Audi A4 1.8 T Quattro vibrate at higher speeds?

Vibrations can be caused by an unbalanced propeller shaft, a worn centre bearing, or play in the inner CV joints. It is vital to inspect these components to prevent subsequent damage to the differential.

Can I replace just the ABS ring, or do I need to replace the entire CV joint?

On the Audi A4 1.8 T Quattro, you can often replace just the ABS ring if it is cracked or corroded, provided that the CV joint itself remains in good condition.

What is included when I buy a CV joint kit from you?

Our kits are complete and include the CV joint, CV boot, high-grade grease, circlips, clamps, and, where applicable, the central hub bolt.

How quickly can I receive spare parts for my Audi?

We aim for fast dispatch across Europe on all stocked items. If you place your order early on a working day, your parts are normally dispatched the very same day.