Drivetrain components and replacement parts for Audi A6 C7.
The Audi A6 C7, produced between 2011 and 2018, represents a high point in German engineering, effortlessly blending comfort with performance. Preserving this balance requires a drivetrain kept in first-class condition. The drivetrain is the system responsible for transferring engine power to the driven wheels, and on a technically refined vehicle like the A6 C7, tolerances are exceptionally strict. Every component, from the gearbox output shafts to the wheel hubs, must work in complete harmony without vibrations or unwanted noises. As driveline specialists, we supply parts matched to original specifications to retain your car's factory ride characteristics.
Maintaining the drivetrain on an Audi A6 C7 is about more than just swapping out parts when they fail; it requires understanding how each component wears over time. Paired with heavy engine configurations and sophisticated multi-link suspension setups, the CV joints and boots endure substantial mechanical loads. We provide the spare parts required to keep your power delivery smooth and quiet, whether you are commuting at motorway speeds or driving through harsh European winters.
The layout of the Audi A6 C7 drivetrain uses Audi’s signature longitudinal configuration, where the engine is mounted along the length of the chassis. This dictates how the drive shafts are angled and how power is distributed. Depending on whether your car is front-wheel drive or fitted with the permanent Quattro all-wheel-drive system, the system's complexity varies. On front-wheel-drive models, torque is transferred directly from the gearbox to the front drive shafts via inner and outer CV joints. On Quattro variants, a propeller shaft and rear differential are added, placing even higher demands on driveline balance.
The outer CV joints on the Audi A6 C7 are engineered to cope with continuous power delivery whilst accommodating tight steering angles. Inside each joint are precision-ground steel balls and raceways lubricated with specialised grease. The entire assembly is sealed by a durable rubber CV boot. If this boot splits, road grit and moisture enter while the grease is slung out, rapidly causing accelerated wear and joint failure. Understanding this configuration helps identify the cause of early symptoms and decide which parts to address during routine servicing.
One of the most frequent signs of drivetrain wear on an Audi A6 C7 is a sharp clicking or knocking noise on full steering lock, such as when negotiating tight corners or parking. This is a classic symptom of a worn outer CV joint on the Audi A6 C7. The noise occurs when the joint’s internal ball bearings lose their smooth track along the raceways due to wear, pitting, or contamination. If neglected, the joint can suffer catastrophic failure, leaving the vehicle completely immobilised.
Vibrations felt during acceleration are another common warning sign, typically pointing to worn inner CV joints or an unbalanced drive shaft. Because the Audi A6 C7 cabin is exceptionally well insulated, even minor driveline vibrations are often felt directly through the steering wheel or seat base. It is also wise to inspect regularly for grease flung across the inner wheel rim or wheel arch lining. This indicates a split CV boot, which is the leading cause of premature constant velocity joint failure. Tackling these warning signs early will often save you from having to replace the complete driveshaft assembly later.
When repairing the transmission and running gear on this chassis, certain components require attention more frequently than others. The outer CV joint is the most heavily stressed part, as it articulates constantly while transmitting power. We recommend inspecting the condition of the drive shaft boots at every service. Here are the primary categories we offer for your Audi A6 C7:
Beyond the joints themselves, it is also common to inspect ABS reluctor rings for corrosion, which can trigger fault codes in the braking and stability systems. While outer joints are the most frequent replacement item, fitting high-quality replacement parts with the correct spline count and dimensions is vital to ensure hassle-free installation and dependable performance.
Navigate directly to the relevant subcategory for your Audi A6 C7:
With multiple drivetrain variants available across this chassis, it pays to begin in the correct category straight away. Comparing the dedicated component groups for the Audi A6 C7 helps you diagnose whether your issue lies with a drive shaft, CV joint, or prop shaft, and leads you directly to the correct fitment.
Sourcing replacement parts for an Audi A6 C7 can be complex, as the platform accommodates a broad spectrum of petrol and diesel engines alongside varied gearboxes such as S-tronic, Multitronic, and Tiptronic. These driveline combinations mean that drive shafts and joints vary in overall length, mounting flange designs, and spline tooth counts. To ensure you order the right part the first time, simply select your car's make, model, and engine variant in our store selector.
Choosing your exact model filters our catalogue so you only see the parts that are technically compatible with your specific car. This takes the guesswork out of ordering an outer CV joint for your Audi A6 C7. Remember to verify whether your car is front-wheel drive or Quattro, as this alters the dimensions of the driveline components. Our database is consistently refined with accurate fitment data to provide a seamless buying experience.
CVJoint24 is the international shop of a Swedish driveline specialist, dispatching directly from our central warehouse in Helsingborg, Sweden, to customers throughout the European Union. Unlike general car parts retailers, we concentrate exclusively on driveline and transmission components. This specialist focus provides you with deep product expertise and an inventory tailored specifically to high-stress driveline applications. When ordering Audi A6 C7 parts with us, you receive reliable, high-specification products designed to meet the demands of modern premium cars.
We combine in-depth technical advice with a straightforward vehicle selector that ensures an exact fit. Our aim is to supply the ideal solutions for your drivetrain, whether you require a simple replacement CV boot or a complete joint assembly. Backed by fast EU-wide delivery and specialist support, we are the trusted choice for Audi drivers seeking quality spare parts without compromise.
The most common symptom is a clicking noise when turning sharply while accelerating. If the sound disappears when driving straight ahead, it is almost certainly a worn outer joint.
No, there are variations depending on engine size, gearbox type and whether the car has Quattro four-wheel drive. Always select your exact make, model and engine to find the right part.
If the boot is torn, grease leaks out and dirt gets in. This destroys the CV joint very quickly, leading to far more expensive repairs than simply replacing the CV boot.
It requires some mechanical experience and the correct tools, including a puller and a torque wrench. For a competent DIY mechanic, it is entirely manageable.
Yes, our outer CV joint kits for the Audi A6 C7 are normally supplied complete with the joint, CV boot, grease, clamps and mounting bolt.
Vibration under acceleration can be caused by worn inner CV joints or an unbalanced drive shaft. It is important to inspect the condition of the complete shaft assembly if vibrations occur.