Audi Q3 2.0 TDI Quattro
Car parts and drivetrain components for Audi Q3 2.0 TDI Quattro. Always check the fit before ordering.
Products for Audi Q3 2.0 TDI Quattro
- Position: Front left
- Total length: 563 mm
- Splines gearbox side: 26
- Splines wheel side: 36
- Position: Front right
- Total length: 610 mm
- Splines gearbox side: 40
- Splines wheel side: 36
- Position: Front right
- Total length: 910 mm
- Splines gearbox side: 37
- Splines wheel side: 36
- Diameter: 30 mm
- Hole spacing c/c: 410 mm
- Bearing thickness: 37 mm
- Position: Inner
- Inner splines: 34
- Outer splines: 37
- Joint diameter: 85 mm
- Position: Outer
- Seal diameter: 59 mm
- Inner splines: 27
- Outer splines: 36
- Joint diameter: 97,95 mm
- Number of centre bearings: 1
- Number of joints: 1
- Total length: 2,260 mm
- Number of centre bearings: 1
- Number of joints: 1
- Total length: 2,160 mm
- Position: Front left
- Flange diameter: 108 mm
- Total length: 488 mm
- Splines wheel side: 36
- Position: Rear left
- Flange diameter: 100 mm
- Total length: 594 mm
- Splines wheel side: 36
- Position: Rear right
- Flange diameter: 100 mm
- Total length: 631 mm
- Splines wheel side: 36
- Position: Front left
- Total length: 562 mm
- Splines gearbox side: 37
- Splines wheel side: 36
- Position: Front left, Inner
- Seal diameter: 31 mm
- Inner splines: 34
- Outer diameter: 85 mm
- Splines gearbox side: 26
- Position: Rear, Inner
- Diameter: 86 mm
- Splines gearbox side: 33
- Width: 34 mm
- Position: Rear, Outer
- Seal diameter: 59 mm
- Inner splines: 33
- Outer diameter: 82 mm
- Splines wheel side: 36
- Position: Inner
- Seal diameter: 100 mm
- Inner splines: 33
- Joint diameter: 100 mm
- Position: Front left
- Flange diameter: 108 mm
- Total length: 486 mm
- Splines wheel side: 36
- Position: Outer
- Seal diameter: 60 mm
- Inner splines: 30
- Outer splines: 36
- Joint diameter: 89,9 mm
- Position: Front right
- Flange diameter: 108 mm
- Joint diameter: 108 mm
- Total length: 795 mm
- Splines wheel side: 36
- Diameter: 30 mm
- Height: 116 mm
- Hole spacing c/c: 228 mm
- Bearing thickness: 15 mm
Frequently Asked Questions about Drivetrain Parts for Audi Q3 2.0 TDI Quattro
How do I know whether the outer or inner CV joint is worn on my Audi Q3?
A worn outer CV joint typically produces a clicking or knocking noise when taking sharp turns. An inner CV joint tends to cause vibrations through the entire car during acceleration, whether you are cornering or driving in a straight line.
Do all drive shafts fit every Audi Q3 2.0 TDI Quattro?
No, there can be differences depending on whether the car has a manual or automatic gearbox (DSG/S tronic), as well as the model year. Always select your car's exact make, model and engine to find the correct version.
What is included when I purchase a CV joint from you?
Our CV joint kits are supplied complete with the joint itself, a model-specific CV boot, high-grade grease, clamps and, where required, a new centre bolt or nut to ensure correct installation.
Can I replace just the propeller shaft centre bearing, or must the complete shaft be replaced?
On certain Audi Q3 models, the centre bearing can be replaced separately, but it is often more cost-effective and dependable to replace the entire propeller shaft if there is also wear in the universal joints.
Why is it important to replace a damaged CV boot immediately?
The boot protects the CV joint from dirt, water and road grit while retaining the lubricating grease. A split boot quickly leads to premature joint wear and failure, resulting in a considerably more expensive repair.
Do you offer a fitment guarantee on parts for Audi Q3 2.0 TDI Quattro?
Yes, we provide a fitment guarantee on all our parts when you select your specific car details upon ordering. This gives you complete peace of mind that you will receive the correct part tailored to your car's drivetrain.