Drive shafts for Citroen Jumper

Looking for a high-quality drive shaft for your Citroen Jumper? As driveline specialists, we supply a comprehensive range of drive shafts specifically engineered to handle the demands of...

Products for Drive shafts for Citroen Jumper

38 products
1 - 24 of 38
Item no.:1109010
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 816 mm
  • Joint diameter: 99 mm
Item no.:2161135
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 1,149 mm
  • Joint diameter: 99 mm
Item no.:2122662
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 1,125 mm
  • Joint diameter: 106 mm
Item no.:7314146
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 28
  • Total length: 759 mm
  • Joint diameter: 100 mm
Item no.:1155327
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 28
  • Total length: 759 mm
  • ABS teeth: 54
Item no.:1199244
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 762 mm
  • ABS teeth: 54
Item no.:2138059
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 1,084 mm
  • ABS teeth: 54
Item no.:7300823
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 752 mm
  • ABS teeth: 54
Item no.:7300698
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 1,084 mm
  • Joint diameter: 113 mm
Item no.:2143585
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 28
  • Total length: 1,077 mm
  • ABS teeth: 54
Item no.:2167567
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 35
  • Total length: 1,055 mm
  • ABS teeth: 54
Item no.:7314199
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 35
  • Total length: 1,055 mm
  • Joint diameter: 113 mm
Item no.:1128105
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 824 mm
  • Joint diameter: 106 mm
Item no.:2127494
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 28
  • Total length: 1,077 mm
  • Joint diameter: 100 mm
Item no.:2112606
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 1,070 mm
  • ABS teeth: 54
Item no.:1102052
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 770 mm
  • Joint diameter: 100 mm
Item no.:7301051
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 770 mm
  • ABS teeth: 54
Item no.:2134763
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 1,070 mm
  • Joint diameter: 100 mm
Item no.:1176271
  • Position: Front left
  • Splines gearbox side: 31
  • Splines wheel side: 35
  • Total length: 749 mm
  • Joint diameter: 106 mm
Item no.:2124500
  • Position: Front right
  • Splines gearbox side: 31
  • Splines wheel side: 35
  • Total length: 1,205 mm
  • Joint diameter: 106 mm
Item no.:1155630
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 770 mm
  • ABS teeth: 54
Item no.:1123442
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 762 mm
  • Joint diameter: 115 mm
Item no.:2158686
  • Position: Front right
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 1,084 mm
  • Joint diameter: 115 mm
Item no.:1155941
  • Position: Front left
  • Splines gearbox side: 41
  • Splines wheel side: 35
  • Total length: 806 mm
  • Joint diameter: 106 mm
Showing 1–24 of 38 products

Drive shafts for Citroen Jumper

The Citroen Jumper is a robust workhorse that is frequently subjected to heavy payloads and demanding driving conditions in daily commercial service. The drive shaft is a critical component in the vehicle's driveline, and for a Citroen Jumper it is vital that these parts maintain the highest quality to avoid costly downtime. Because the Jumper is available in many different configurations – from nimble vans to large dropside pickups and buses – drive shaft specifications vary considerably depending on wheelbase, payload capacity and engine option. At CVJoint24, we specialise in supplying precisely the right components for your specific model. By choosing a model-matched drive shaft, you ensure that engine power is transferred smoothly from the gearbox to the wheels without losses or disruptive vibrations. Our range is carefully selected to meet the technical demands of Citroen commercial vehicles, giving you complete confidence that your replacement part will perform as well as the original or better for a long time to come.

Maintaining the drivetrain on a commercial vehicle demands components capable of withstanding high torque and constant strain. A driveshaft for the Jumper is not merely a metal bar; it is a precision component engineered to cope with suspension travel and steering angles under load. We understand how critical vehicle uptime is to your business, which is why we only supply parts proven to cope with demanding European conditions, whether for stop-start urban deliveries or long-distance motorway haulage.

What does a drive shaft do on a Citroen Jumper?

The primary role of the drive shaft on a front-wheel-drive vehicle like the Citroen Jumper is to transfer the torque generated by the engine, via the gearbox, directly to the front road wheels. It consists of a solid or tubular shaft bar fitted with an inner and an outer CV joint. These joints are essential to allow for front suspension travel and steering angles while ensuring power delivery remains smooth and continuous. For a commercial van, this is especially demanding, as joint operating angles can become extreme under heavy loads or when driving across uneven surfaces.

The drive shaft must be dimensioned to handle the substantial torque produced by modern diesel engines, particularly during hill starts or hard acceleration with a full payload. Beyond basic power transmission, the drive shaft plays a crucial role in overall ride comfort; a properly balanced and straight shaft minimises chassis vibrations and protects other components, such as wheel bearings and gearbox mounts, from premature wear. Understanding the central function of the drive shaft helps you recognise the importance of replacing it before total failure occurs. A snapped drive shaft results in an immediate loss of drive, leaving the vehicle stranded, which can be both hazardous and costly when on an active job.

Common signs of wear

Several clear symptoms indicate that a drive shaft on your Citroen Jumper is nearing the end of its service life. One of the most common signs is a rhythmic clicking or knocking noise clearly heard when cornering sharply at low speeds. This typically points to a worn outer constant velocity joint with excessive play in its internal bearing tracks. If you instead experience severe vibrations through the steering wheel or the entire bodywork under acceleration, it may indicate a worn inner CV joint, where the tripod needle bearings have worn grooves into the housing.

Other visual warning signs include grease splattered across the inside of the wheel rim or around the wheel arch. This is almost invariably caused by a split or damaged CV boot. Once the boot fails, road dirt, grit and water penetrate the joint while essential lubricating grease is thrown out, leading to rapid deterioration of the precision-machined metal surfaces. Finally, a damaged or cracked ABS ring can trigger dashboard warning lights or cause erratic ABS intervention under braking. Because the ABS ring is often fitted directly onto the outer CV joint, it is best practice to inspect or replace these parts together to keep the vehicle's safety systems fully operational.

How to choose the correct drive shaft

Selecting the right drive shaft for a Citroen Jumper can seem complex due to the numerous technical variations across model years, engines and chassis specifications. Significant differences exist in overall shaft length, spline counts on both the gearbox and wheel hub ends, and whether the vehicle is equipped with an ABS system. Furthermore, drive shafts frequently differ between manual and automatic transmissions. To ensure you order the exact part required, use our make, model and engine selector. This filters our catalogue to show only the components that are technically compatible with your specific Jumper.

It is also essential to check whether your vehicle features heavy-duty suspension or is a "Heavy" chassis version (often fitted with 16-inch wheels as standard), as these models regularly require heavy-duty drive shafts with larger dimensions than standard versions. By paying close attention to technical specifications, you avoid unnecessary returns and ensure your repair proceeds without delay. At CVJoint24, we provide the technical expertise and catalogue tools needed to select the correct part straight away for a perfect fit in your drivetrain.

Related parts to inspect

Please also check these exact pages for the same vehicle when working on the drive shaft:

When a driveline component shows wear, adjacent parts on the vehicle often require inspection as well. Comparing these exact pages for the Citroen Jumper makes it easier to determine whether an issue lies with the drive shaft itself or with a related part of the power transmission.

This is particularly relevant on commercial models where vibrations, play and unusual noises can travel between several driveline components. Checking related categories reduces the risk of replacing one correct component while overlooking an adjacent worn part that contributes to the same problem.

Carrying out a comprehensive inspection of the front suspension and drivetrain ensures that your Citroen Jumper remains dependable for miles to come. It is often the smaller details, such as a fresh drive shaft boot or a new ABS reluctor ring, that determine how long your new drive shaft will last.

Why shop with CVJoint24?

CVJoint24 is the international shop of a Swedish driveline and power transmission specialist, dispatching directly from our central warehouse in Helsingborg, Sweden, to customers across the European Union. We have built deep technical expertise around these core components, allowing us to offer an extensive range that few general motor factors can match. We know that your Citroen Jumper is an indispensable tool for your work or daily routine, which is why we never compromise on product quality. With our commitment to precise fitment and manufacturing accuracy, you can trust every part we supply to meet rigorous standards.

When you order from us, you benefit from our accurate fitment guarantee by simply selecting your car's make, model and engine. We dispatch quickly across the EU to minimise your van's time off the road. Our customer support team possesses in-depth technical knowledge and is always on hand to assist with installation advice or parts selection. Choosing CVJoint24 means securing premium spare parts alongside a reliable partner dedicated to keeping your vehicle running smoothly with durable, high-grade components.

Frequently asked questions about drive shafts for Citroen Jumper

How do I know if my Citroen Jumper needs a new drive shaft?

The most common signs are clicking noises when cornering (outer joint), body vibrations during acceleration (inner joint) or visible grease leaks from split CV boots.

Can I replace just the CV joint instead of the entire drive shaft?

Yes, if the shaft itself is straight and undamaged, you can often replace the outer or inner CV joint separately, which can be a more economical option.

Do all Jumper drive shafts fit regardless of engine size?

No, drive shafts differ depending on the engine (e.g. 2.2 HDi vs 3.0 HDi), gearbox type and whether the van has the heavier 'Heavy' chassis. Always select your vehicle make, model and engine to find the right part.

What is included when I buy a complete drive shaft from you?

Our complete drive shafts are normally supplied fully assembled with both the inner and outer CV joint, CV boots and necessary fitting accessories such as the hub nut.

Why does my Citroen Jumper vibrate under acceleration?

This is a classic symptom of a worn inner CV joint. When play develops in the joint, it creates an imbalance in the drivetrain that feels like vibrations throughout the van under load.

Is it difficult to replace a drive shaft on a Citroen Jumper myself?

It requires some mechanical experience, the right tools (including large sockets for the hub nut) and the ability to raise and support the van safely, but it is a fully achievable job for a competent DIY mechanic.