Drive shafts for Fiat Fiorino

Explore our targeted selection of drive shafts engineered for the Fiat Fiorino range. Our catalogue covers diesel, petrol, and natural gas versions, including the 1.3 D Multijet and...

Products for Drive shafts for Fiat Fiorino

40 products
25 - 40 of 40
Item no.:110654
  • Position: Front left
  • Splines wheel side: 22
  • Total length: 557 mm
  • Joint diameter: 81 mm
  • Tripod shaft diameter: 32 mm
Item no.:2110020
  • Position: Front right
  • Splines wheel side: 20
  • Total length: 793 mm
  • Diameter 1: 80 mm
Item no.:1134907
  • Position: Front left
  • Splines wheel side: 20
  • Total length: 547 mm
  • Diameter 1: 80 mm
Item no.:2144448
  • Position: Front right
  • Splines gearbox side: 35
  • Splines wheel side: 25
  • Total length: 543 mm
  • Joint diameter: 85 mm
Item no.:2154022
  • Position: Front right
  • Splines wheel side: 20
  • Total length: 812 mm
  • Diameter 1: 80 mm
Item no.:1191206
  • Position: Front left
  • Splines wheel side: 20
  • Total length: 533 mm
  • Diameter 1: 80 mm
Item no.:1113729
  • Position: Front left
  • Splines gearbox side: 34
  • Splines wheel side: 25
  • Total length: 480 mm
  • Joint diameter: 82 mm
Item no.:2178864
  • Position: Front right
  • Splines gearbox side: 34
  • Splines wheel side: 25
  • Total length: 522 mm
  • Joint diameter: 82 mm
Item no.:1141265
  • Position: Front left
  • Splines wheel side: 22
  • Total length: 531 mm
  • Joint diameter: 80 mm
  • Tripod shaft diameter: 28 mm
Item no.:2152803
  • Position: Front right
  • Splines wheel side: 22
  • Total length: 815 mm
  • Joint diameter: 80 mm
  • Tripod shaft diameter: 28 mm
Item no.:1176300
  • Position: Front left
  • Splines wheel side: 20
  • Total length: 547 mm
  • Joint diameter: 80 mm
  • Tripod shaft diameter: 25 mm
Item no.:2144025
  • Position: Front right
  • Splines wheel side: 20
  • Total length: 793 mm
  • Joint diameter: 80 mm
  • Tripod shaft diameter: 25 mm
Item no.:1149323
  • Position: Front left
  • Splines wheel side: 22
  • Total length: 558 mm
  • Joint diameter: 80 mm
  • Tripod shaft diameter: 32 mm
Item no.:2167343
  • Position: Front right
  • Splines wheel side: 22
  • Total length: 862 mm
  • Joint diameter: 80 mm
  • Tripod shaft diameter: 32 mm
Item no.:217677
  • Splines gearbox side: 24
  • Splines wheel side: 25
  • Total length: 950 mm
Item no.:116847
  • Splines wheel side: 25
  • Total length: 480 mm
  • Thread size: M24x1.5
Showing 25–40 of 40 products

Frequently Asked Questions about Drive Shafts for Fiat Fiorino

How do I know whether the right or left drive shaft is faulty on my Fiat Fiorino?

If you hear a clicking noise when turning left, it is usually the right outer CV joint that is under load and worn, and vice versa. However, vibrations under acceleration may require a closer inspection of both inner CV joints.

Can I replace just the CV joint instead of the entire drive shaft on my Fiorino?

Yes, if the shaft bar itself is straight and undamaged, you can save money by replacing only the worn inner or outer CV joint. We supply both complete driveshafts and individual joints.

Does the same drive shaft fit both petrol and diesel models of the Fiat Fiorino?

Not always. Dimensions and splines can vary depending on whether the vehicle is fitted with a 1.3 Multijet diesel or a 1.4 petrol engine. Always select your exact make, model and engine to ensure you get the correct version.

What happens if a drive shaft snaps completely while driving?

If a drive shaft snaps, the vehicle will lose all drive to that wheel. Because the Fiorino uses an open differential, all engine power will spin the broken side, leaving the van stationary even with a gear engaged.

Are the CV joints included when I buy a complete drive shaft from you?

Yes, when you order a complete drive shaft from CVJoint24, it arrives fully assembled with both the inner and outer CV joint as well as the CV boots, ready for direct installation.

Do I need a wheel alignment after replacing a drive shaft on my Fiat?

It is not strictly necessary if no track rod ends or suspension arms have been removed in a way that alters the wheel geometry, but it is often recommended as a sensible precaution to ensure optimal tyre wear.