Drive shafts for Peugeot 407 SW

Need a replacement drive shaft for your Peugeot 407 SW? As driveline specialists, we stock a curated selection of drive shafts tailored specifically for this popular estate. Our...

Products for Drive shafts for Peugeot 407 SW

16 products
1 - 16 of 16
Item no.:1168569
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 670 mm
  • Diameter 1: 100 mm
Item no.:2183374
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 973 mm
Item no.:2148183
  • Position: Front right
  • Splines gearbox side: 24
  • Splines wheel side: 28
  • Total length: 958 mm
  • Joint diameter: 92 mm
Item no.:1148622
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 655 mm
  • Joint diameter: 95 mm
Item no.:2140948
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 998 mm
  • Joint diameter: 95 mm
Item no.:1123910
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 620 mm
  • Joint diameter: 92 mm
Item no.:2174857
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 950 mm
  • Joint diameter: 90 mm
Item no.:1163161
  • Position: Front left
  • Splines gearbox side: 26
  • Splines wheel side: 28
  • Total length: 661 mm
  • Joint diameter: 86 mm
Item no.:2128247
  • Position: Front right
  • Splines gearbox side: 26
  • Splines wheel side: 28
  • Total length: 870 mm
  • Joint diameter: 86 mm
Item no.:216818
  • Position: Front
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 980 mm
  • Joint diameter: 92 mm
Item no.:1161090
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 28
  • Total length: 678 mm
  • Joint diameter: 92 mm
Item no.:1128484
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 676 mm
  • Seal ring diameter: 59 mm
Item no.:218021
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 973 mm
  • Joint diameter: 95 mm
Item no.:1186300
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 28
  • Total length: 670 mm
  • Joint diameter: 86 mm
Item no.:1183081
  • Position: Front left
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 642 mm
  • Joint diameter: 100 mm
Item no.:2139650
  • Position: Front right
  • Splines gearbox side: 37
  • Splines wheel side: 28
  • Total length: 942 mm
  • Joint diameter: 100 mm

Drive shafts for Peugeot 407 SW

The Peugeot 407 SW is an estate renowned for its comfort and poised road holding, but maintaining that refined driving experience requires a drivetrain in peak condition. The drive shaft is one of the most critical components in the car's power delivery, responsible for transferring torque directly from the gearbox to the wheels. On a front-wheel-drive car such as the 407 SW, these shafts endure substantial stress, particularly under heavy acceleration and over uneven road surfaces. At CVJoint24, we understand how vital it is to fit the correct parts to your vehicle. Our range for the Peugeot 407 SW is engineered to meet strict standards for durability and precision. Whether you drive an efficient HDi diesel or a punchy petrol model, we have the components you need for a smooth, vibration-free ride. Choosing the right spare part is essential for your vehicle's longevity and your safety on the road.

What does a drive shaft do on a Peugeot 407 SW?

The primary role of the drive shaft on a Peugeot 407 SW is to serve as the vital link between the engine and gearbox assembly and the driven front wheels. It consists of a solid or tubular shaft fitted with joints at each end. The inner joint mounts to the gearbox, allowing the driveshaft to plunge in and out as the suspension articulates, whilst the outer joint sits at the wheel hub, facilitating steering angles while continuously transmitting rotational force. Without a functional drive shaft, engine torque would never reach the road, making it a cornerstone of the vehicle's running gear. On the 407 SW estate, these components are engineered to manage the car's weight and torque output, but over time the moving parts inside the joints will wear. A properly functioning shaft minimises drivetrain losses and ensures your Peugeot responds instantly to throttle input without unnatural noise or imbalance, preserving the model's signature ride quality.

Common signs of wear

There are several telltale symptoms indicating that a drive shaft on your Peugeot 407 SW is worn or failing. One of the most frequent warnings is a rhythmic clicking or knocking sound when turning on full lock at low speeds, which usually points to a worn-out outer CV joint. If you experience distinct vibrations through the cabin or steering wheel during acceleration, it often suggests that the inner joint has developed excessive play or that the shaft itself has warped. You should also inspect the area for grease splattered inside the wheel rim or around the wheel arch, typically caused by a split or torn CV boot. Once the protective grease escapes and dirt enters, joint failure quickly follows. Ignoring these warning signs can ultimately cause the driveshaft to snap, leaving you stranded with a total loss of drive. Early inspection saves substantial time and expense.

Choosing the correct drive shaft

Finding the right drive shaft for a Peugeot 407 SW might seem daunting initially, as specifications vary across engine sizes, gearbox types and production years. Differences include overall length, spline count and whether the car runs a manual or automatic transmission. To make selection straightforward and reliable, simply filter our range by selecting your vehicle's make, model and engine variant. This ensures you only see parts matched precisely to your car's exact mechanical specification. Always verify which side of the vehicle requires replacement, as the left-hand and right-hand shafts differ in length due to the offset position of the gearbox. Our focus is to help you get the exact part right first time, avoiding inconvenient returns and getting your estate back on the road without delay.

Related parts to inspect

We recommend checking these exact pages for the same vehicle when working on the drive shaft:

When a drivetrain component develops wear, neighbouring assemblies on the same vehicle should be inspected as well. By cross-referencing these exact pages for the Peugeot 407 SW, you can easily determine whether a fault lies purely within the drive shaft or in an adjacent area of the driveline.

This is especially important on models where vibrations, play and unwanted noises can travel between multiple drivetrain components. A brief inspection of related categories prevents replacing a single part only to find an adjoining worn component still producing the same fault.

Why buy from CVJoint24?

CVJoint24 is the international shop of a Swedish driveline specialist, backed by our central warehouse in Helsingborg, Sweden. We combine in-depth engineering knowledge with an extensive stock profile to deliver dependable solutions for your Peugeot 407 SW. When you order from us, you receive a high-grade replacement car part supported by our accurate fitment commitment. We know how crucial your vehicle is for daily motoring, which is why we process orders promptly for reliable delivery across the EU. Our goal is to ensure you find the right component straight away; by filtering via your car's make, model and engine, the risk of ordering the wrong part is minimised. Because we focus purely on driveline systems, we offer specialist support and targeted components that generic motor factors cannot match. Turn to CVJoint24 for dependable parts, accurate fitment and a drivetrain built for thousands of kilometres ahead.

Frequently asked questions about drive shafts for Peugeot 407 SW

How do I know which drive shaft fits my Peugeot 407 SW?

The most reliable way is to select your Peugeot 407 SW by make, model and engine variant in our search filter. This filters our range to show the drive shafts that are technically compatible with your car's engine and gearbox.

Can I replace just the CV joint instead of the entire shaft?

Yes, provided the shaft bar itself is undamaged, you can often replace just the inner or outer CV joint. We supply both complete drive shafts and individual CV joints to give you the most cost-effective option.

Why does my Peugeot 407 SW vibrate during acceleration?

Vibration under acceleration is often caused by wear in the inner CV joint. When play develops in the joint, it creates an imbalance that travels through the drivetrain and can be felt through the car's bodywork.

Is there a difference between drive shafts for manual and automatic gearboxes?

Yes, the length of the shaft or the spline count frequently differs between manual and automatic models. Always check the technical specifications carefully before ordering.

How often do CV boots need replacing on a 407 SW?

There is no fixed replacement interval, but the CV boots should be inspected at every service. If they are cracked or split, they must be replaced immediately to prevent dirt from ruining the CV joint.

Is an ABS ring included when I purchase a complete drive shaft?

This varies between parts. Many of our complete drive shafts come with a pre-fitted ABS ring, but always check the product description to make sure.