Drive shafts for Rover 200

Looking for a replacement drive shaft for your Rover 200? At CVJoint24 you will find an extensive selection of drive shafts tailored specifically to your vehicle's technical...

Products for Drive shafts for Rover 200

43 products
1 - 24 of 43
Item no.:1150392
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 641 mm
  • Diameter 1: 82 mm
Item no.:2166385
  • Position: Front right
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 880 mm
  • Diameter 1: 82 mm
Item no.:2119061
  • Position: Front right
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 880 mm
  • ABS teeth: 43
Item no.:1121053
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 641 mm
  • ABS teeth: 43
Item no.:2125064
  • Position: Front right
  • Splines gearbox side: 25
  • Splines wheel side: 26
  • Total length: 613 mm
  • ABS teeth: 50
Item no.:1118037
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 26
  • Total length: 610 mm
  • Joint diameter: 85 mm
Item no.:1142713
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 26
  • Total length: 610 mm
  • ABS teeth: 50
Item no.:2108728
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 26
  • Total length: 597 mm
  • Joint diameter: 84 mm
Item no.:2112022
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 26
  • Total length: 597 mm
  • ABS teeth: 50
Item no.:1195939
  • Position: Front left
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 588 mm
  • Diameter 1: 92 mm
Item no.:2171444
  • Position: Front right
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 938 mm
  • Diameter 1: 92 mm
Item no.:1187209
  • Position: Front left
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 588 mm
  • ABS teeth: 27
Item no.:2174478
  • Position: Front right
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 938 mm
  • ABS teeth: 27
Item no.:1180844
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 641 mm
  • ABS teeth: 27
Item no.:2160617
  • Position: Front right
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 880 mm
  • ABS teeth: 27
Item no.:2177306
  • Position: Front right
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 938 mm
  • ABS teeth: 43
Item no.:1110003
  • Position: Front left
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 587 mm
  • ABS teeth: 43
Item no.:1193492
  • Position: Front left
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 587 mm
  • Joint diameter: 91,9 mm
Item no.:2121653
  • Position: Front right
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 936 mm
  • Joint diameter: 91,9 mm
Item no.:1196732
  • Position: Front left
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 587 mm
  • ABS teeth: 27
Item no.:2183792
  • Position: Front right
  • Splines gearbox side: 29
  • Splines wheel side: 26
  • Total length: 936 mm
  • ABS teeth: 27
Item no.:1164412
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 642 mm
  • Joint diameter: 84 mm
Item no.:2153318
  • Position: Front right
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 880 mm
  • Joint diameter: 84 mm
Item no.:1131172
  • Position: Front left
  • Splines gearbox side: 22
  • Splines wheel side: 26
  • Total length: 642 mm
  • ABS teeth: 43
Showing 1–24 of 43 products

Drive shafts for Rover 200

The Rover 200 is a car that demands precision when it comes to driveline replacement parts. A drive shaft for Rover 200 models is far more than just a steel bar; it is a finely balanced component engineered to transmit engine torque across varying angles and suspension loads. We have assembled a comprehensive range of drive shafts catering to the different generations and engine options available for this car. Our broad selection allows us to offer solutions for virtually every requirement, whether you need a left- or right-hand side replacement. Maintaining the drivetrain on an older Rover is essential for preserving driving dynamics and road safety. By choosing a model-matched driveshaft, you ensure vibrations are minimised and torque is delivered smoothly without placing unnecessary wear on the gearbox. Our parts are carefully chosen to meet strict standards for material quality and durability, making them an excellent choice for enthusiasts and everyday motorists who want dependable components for their Rover.

What does a drive shaft do on a Rover 200?

The drive shaft on a Rover 200 carries out the vital role of transferring rotational force from the gearbox out to the driven front wheels. Because the Rover 200 is front-wheel drive, the drive shafts endure high loads, particularly under acceleration and sharp cornering. The complete shaft assembly includes the central shaft together with inner and outer joints that permit the wheels to travel up and down with the suspension while steering freely. Without an intact drive shaft, drive cannot reach the road surface and the vehicle remains stationary. The inner joint connects to the gearbox and primarily handles vertical suspension articulation over uneven road surfaces, while the outer constant velocity joint sits at the wheel hub to enable steering. For Rover 200 owners, it is important to remember that these drivetrain parts work in harsh conditions, dealing with heat, dirt and continuous movement. A properly functioning driveshaft ensures smooth running and prevents imbalances from damaging surrounding chassis components. Understanding these mechanics makes it easier to spot issues before they cause costly breakdowns on the road.

Common symptoms of wear

Several distinct signs suggest that a drive shaft on your Rover 200 is nearing the end of its service life. One of the most frequent symptoms is a clicking or knocking noise clearly audible when turning at low speeds, such as during parking manoeuvres. This usually indicates that the outer CV joint is worn and has developed excessive play. Vibrations felt through the steering wheel or car floor during acceleration typically point to a worn inner joint or an unbalanced shaft. If you spot grease splattered on the inside of the road wheel or across the wheel arch, a CV boot has split, allowing grit and moisture to enter and ruin the internal components quickly. A whining sound that rises with vehicle speed may also indicate failing bearings or damaged mountings. It is crucial to address these symptoms promptly, as a snapped drive shaft will leave you stranded without drive. Regularly inspecting your rubber boots remains the most reliable way to avoid full drive shaft replacements on your Rover.

Choosing the correct drive shaft

Selecting the right drive shaft for Rover 200 models requires attention to detail, as technical specifications vary depending on engine size, gearbox type and whether the car is fitted with ABS. The overall compressed length of the shaft and the precise spline count on both ends must match your original setup for a trouble-free installation. Manual and automatic gearboxes often use different shaft designs, and engine sizes such as 1.4, 1.6 or 2.0 litres frequently require distinct shaft dimensions. The most reliable approach is to select your vehicle's exact make, model and engine variant in our store. This filters our catalogue down to shafts that match your Rover's exact technical configuration, eliminating guesswork and saving valuable workshop time. We also recommend checking whether your car has anti-lock brakes, as the drive shaft will need to come equipped with the correct sensor reluctor ring. Careful selection ensures your Rover 200 regains its original reliability and continues to run seamlessly for many miles ahead.

Related parts to check

Please also check these exact pages for the same vehicle when working on the drive shaft:

When a driveline component wears out, related components on the same car often require attention too. Comparing these exact pages for Rover 200 helps you determine whether a fault lies purely with the drive shaft or stems from an adjacent part of the drivetrain.

This is especially true on vehicles where vibrations, play and knocking sounds can travel between interconnected driveline assemblies. A quick inspection of related categories prevents you from replacing one component while overlooking another worn part that produces the very same symptoms.

Replacing these components while the drive shaft is already removed saves considerable time and labour in the long run.

Why buy from CVJoint24?

CVJoint24 is the international shop of a Swedish driveline specialist shipping across the EU from our central warehouse in Helsingborg, Sweden. We appreciate the importance of getting the right part for your Rover 200 on the first attempt, especially when ordering complex drivetrain components such as drive shafts. That is why we provide an accurate fitment guide based on your exact vehicle model and engine. Thanks to our specialist knowledge and comprehensive stock, we guarantee high-quality parts and rapid order dispatch. By focusing dedicatedly on drivetrain components, we offer a level of technical expertise that general motor factors rarely match. When you order from us, you receive a reliable spare part built to strict durability standards, backed by fast dispatch across Europe to get your car back on the road without delay. Trust a specialist who puts your vehicle's performance and peace of mind first.

Frequently Asked Questions about Drive Shafts for Rover 200

How do I know if the drive shaft on my Rover 200 needs replacing?

The most common symptoms are clicking noises when cornering, vibrations under acceleration, or visible grease leaks from split CV boots. If the vibrations increase with road speed, it is often a sign of imbalance or wear in the shaft's joints.

Do all drive shafts fit every Rover 200 model?

No, there are significant differences depending on the engine (such as 1.4 vs 2.0), the gearbox (manual or automatic), and whether the car has ABS. Always select your vehicle's make, model, and engine to find the exact specification for your car.

Are CV joints included when I buy a complete drive shaft?

Yes, when you purchase a complete drive shaft from us, it is normally supplied with both inner and outer CV joints as well as fitted CV boots, ready for direct installation on your Rover 200.

Can I replace just the CV boot instead of the complete drive shaft?

If you catch a split boot early before dirt and moisture have damaged the joint, replacing just the CV boot may be sufficient. If unusual noises are already present, the joint or shaft is usually worn to the point where complete replacement is necessary.

What is the difference between the left and right drive shaft on a Rover 200?

The drive shafts often differ in length between the left and right sides due to the position of the gearbox. It is therefore crucial to verify which side needs replacement before placing your order.

Do you offer a fitment guarantee on drive shafts for Rover?

Yes, we offer a fitment guarantee when you select your specific car model and engine variant. This ensures that the part will fit your Rover 200, provided the vehicle's original factory specifications have not been modified.