Inner CV joints for BMW 3 Serie 325 D E92

Looking for an inner CV joint for your BMW 3 Serie 325 D E92? At CVJoint24 you will find vehicle-specific parts engineered to keep torque transfer from the gearbox to the wheels...

Products for Inner CV joints for BMW 3 Serie 325 D E92

4 products
1 - 4 of 4
Item no.:0428519
  • Position: Rear, Inner
  • Inner splines: 28
  • Outer diameter: 108 mm
Item no.:0428438
  • Position: Rear, Inner
  • Inner splines: 28
  • Splines gearbox side: 28
  • Joint diameter: 108 mm
Item no.:647228
  • Position: Rear, Inner
  • Inner splines: 25
  • Seal diameter: 86 mm
  • Joint diameter: 99 mm
Item no.:649595
  • Position: Rear, Inner
  • Inner splines: 25
  • Total length: 26 mm

Inner CV joints for BMW 3 Serie 325 D E92

The BMW 3 Serie 325 D E92 is a car renowned for its balance of performance and comfort. Maintaining these characteristics requires every component in the drivetrain to function flawlessly. The inner CV joint is a critical part that is often overlooked until problems arise. At CVJoint24, we specialise in these exact components to give your BMW 3 Serie 325 D E92 the care it deserves. We understand the technical demands placed on a high-torque car and ensure our range meets these specifications with the highest possible precision, delivering a long service life and optimum performance under all driving conditions.

What does an inner CV joint do on a BMW 3 Serie 325 D E92?

The primary job of the inner constant velocity joint is to transfer torque from the gearbox or differential to the drive shaft, whilst accommodating suspension travel. Unlike the outer CV joint, which handles steering angles, the inner joint mainly works to compensate for length changes as the car moves up and down over road imperfections. For a BMW 325 D E92, this means the joint must withstand significant forces under acceleration, especially given the punchy nature of the diesel engine. If this component fails, the vehicle's stability and power delivery are compromised, which can lead to consequential damage to other drivetrain parts if left unattended.

Common signs of wear

Wear in an inner CV joint often shows up differently than in an outer joint. The most common symptom is vibration through the body shell under acceleration, typically felt most distinctly between 50 and 90 km/h. Unlike wheel imbalance, these vibrations usually disappear as soon as you lift off the accelerator. Another sign is knocking or clunking noises under load. If the CV boot has split, grease will escape and dirt can penetrate, accelerating wear dramatically. It is therefore vital to inspect the condition of the joint regularly to avoid a total breakdown on the road, which can be costly and compromise road safety.

How to choose the correct inner CV joint

Selecting the right part for a BMW E92 can be tricky, as specifications can vary depending on model year and equipment. The most reliable way to find the right part is to filter by your car's make, model and engine. We have carefully categorised our range to ensure you receive an inner CV joint with the exact spline count and dimensions required. Because we focus on quality, we always recommend checking whether it is time to replace the complete Drive shafts for BMW 3 Serie 325 D E92 if wear is extensive, as this is often more cost-effective in the long run than replacing individual parts repeatedly.

Related parts to check

Be sure to check these exact pages for the same vehicle when working on the inner CV joint:

When one drivetrain component shows wear, adjacent parts on the same car often require inspection as well. By comparing these exact pages for the BMW 3 Serie 325 D E92, it becomes much easier to determine whether the fault lies strictly with the inner CV joint or with an adjacent part of the driveline.

This is particularly relevant on models where vibrations, play and noises can transfer symptoms across several parts in the same drivetrain. A quick check of related categories reduces the risk of replacing the right type of part while overlooking a neighbouring component that contributes to the same issue.

When you are already working on the inner CV joint, it is sensible to inspect the rest of the driveline. A worn inner joint can sometimes indicate that other components are also nearing the end of their life. Here are several parts relevant to your model that you should check to ensure a comprehensive repair:

  • Outer CV joints for BMW 3 Serie 325 D E92 - Check CV boots and listen for clicking noises on full steering lock.
  • Propeller shafts for BMW 3 Serie 325 D E92 - Vibrations can also originate here, especially at motorway speeds.
  • Propeller shaft centre bearings for BMW 3 Serie 325 D E92 - A worn centre bearing can cause similar vibrations to a faulty inner CV joint.
  • ABS rings for BMW 3 Serie 325 D E92 - Take the opportunity to inspect the ring for corrosion or cracks while the wheel is off.

Why buy from CVJoint24?

CVJoint24 is the international shop of a Swedish driveline specialist, with our central warehouse in Helsingborg, Sweden. We combine in-depth technical expertise with an extensive product range tailored to European vehicles. When you purchase an inner CV joint for your BMW from us, you receive a precision car part backed by our fitment guarantee. We aim to help you get the right part first time and dispatch promptly across the EU to minimise your car's time in the garage. With a strict focus on quality, durability and customer satisfaction, we are your dependable partner for reliable drivetrain spares.

Frequently asked questions about inner CV joints for BMW 3 Serie 325 D E92

What are the symptoms of a worn inner CV joint on a BMW E92?

The most common signs are vibrations throughout the entire car during acceleration, frequently at speeds between 50 and 90 km/h, which stop when you lift off the accelerator.

Can I replace just the inner CV joint instead of the entire drive shaft?

Yes, on the BMW 3 Serie 325 D E92, you can often replace only the inner joint provided that the shaft itself and the outer joint remain in good condition.

How do I find the correct inner CV joint for my BMW 325 D?

The easiest and most reliable method is to select your exact make, model and engine variant in our search filter. This ensures that the parts shown are fully compatible with your vehicle.

Is everything required for the replacement included in the kit?

Yes, when you purchase an inner CV joint from us, it usually comes complete with the CV boot, grease, clamps and any circlips needed for a thorough installation.

Why does the inner CV joint wear faster on a diesel car such as the 325 D?

Diesel engines generate significant torque at low revs, which puts greater strain on drivetrain components, particularly the inner joints during heavy load.

How quickly will my new CV joint be dispatched?

We aim to dispatch your order as quickly as possible. For in-stock items, we ensure prompt shipping directly from our central warehouse to customers across Europe.