Volkswagen Bora 1.9 TDI 4MOTION
Car parts and drivetrain components for Volkswagen Bora 1.9 TDI 4MOTION. Always check the fit before ordering.
Products for Volkswagen Bora 1.9 TDI 4MOTION
- Position: Inner
- Seal diameter: 94 mm
- Inner splines: 33
- Number of joints: 3
- ABS teeth: 0
- Diameter: 30 mm
- Hole spacing c/c: 188 mm
- Bearing thickness: 13 mm
- Position: Inner
- Inner splines: 28
- Joint diameter: 108 mm
- Position: Outer
- Seal diameter: 53 mm
- Inner splines: 27
- Outer splines: 36
- Joint diameter: 97,5 mm
- Number of centre bearings: 1
- Number of joints: 1
- Total length: 2,160 mm
- Position: Front left
- Flange diameter: 108 mm
- Total length: 518 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 108 mm
- Total length: 655 mm
- Splines wheel side: 36
- Position: Front left
- Flange diameter: 100 mm
- Total length: 556 mm
- Splines wheel side: 36
- ABS teeth: 0
- Position: Front right
- Flange diameter: 100 mm
- Total length: 822 mm
- Splines wheel side: 36
- Position: Rear left
- Diameter: 81 mm
- Total length: 650 mm
- Splines wheel side: 36
- Position: Rear right
- Diameter: 81 mm
- Total length: 523 mm
- Splines wheel side: 36
- Position: Outer
- Inner splines: 30
- Outer diameter: 81 mm
- Splines wheel side: 36
- Position: Front left
- Flange diameter: 123 mm
- Total length: 518 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 123 mm
- Total length: 810 mm
- Splines wheel side: 36
- Total length: 646 mm
- Splines wheel side: 36
- ABS teeth: 0
- Position: Inner
- Seal diameter: 100 mm
- Inner splines: 33
- Joint diameter: 100 mm
- Position: Outer
- Seal diameter: 52 mm
- Inner splines: 27
- Outer splines: 36
- Joint diameter: 98 mm
Frequently Asked Questions about the Drivetrain for Volkswagen Bora 1.9 TDI 4MOTION
Do drive shafts from a standard front-wheel-drive Bora fit a 4MOTION?
No, the drive shafts on a 4MOTION model are unique in their design, especially at the rear where a front-wheel-drive car has none at all. Even the front shafts can differ in length and mounting due to the bevel box.
What are the most common signs of a worn inner CV joint on my Bora 1.9 TDI?
The most common symptoms are vibrations through the chassis during acceleration, often noticeable at speeds between 70 and 100 km/h. Unlike outer joints, clicking noises when turning are rarely heard.
How often does the propeller shaft on a Bora 4MOTION need servicing?
The propeller shaft itself is virtually maintenance-free, but you should regularly inspect the condition of the centre bearing and rubber coupling discs (guibo joints). Cracks in the rubber or noise from the bearing indicate that replacement is necessary.
Why is it important to replace a split CV boot immediately?
A split CV boot allows the protective grease to be thrown out while dirt, water and road salt penetrate the CV joint. This causes extremely rapid wear and can lead to complete failure of the CV joint within just a few kilometres.
Can a cracked ABS ring affect the four-wheel-drive system?
Yes, absolutely. The Haldex system in your Bora 4MOTION uses signals from the ABS sensors to determine how to distribute power. An erroneous signal from a cracked ABS ring can cause the all-wheel drive to behave erratically or disengage completely.
Do you offer a fitment guarantee on all drivetrain parts?
Yes, when you select parts by your Volkswagen Bora 1.9 TDI 4MOTION model and engine specifications, your purchase is covered by our fitment guarantee. It is our promise to you that you will receive the correct part straight away.