Audi 100 Avant 2.0 D

Spare parts and drivetrain components for the Audi 100 Avant 2.0 D. Select your make, model and engine to confirm correct fitment before ordering.

Products for Audi 100 Avant 2.0 D

19 products
1 - 19 of 19
Item no.:0495470
  • Position: Inner
  • Inner splines: 28
  • Seal diameter: 108 mm
  • Total length: 32 mm
  • Joint diameter: 108 mm
Item no.:0544590
  • Position: Outer
  • Inner splines: 25
  • Seal diameter: 56 mm
  • Outer splines: 26
  • ABS teeth: 46
Item no.:0672254
  • Total length: 92 mm
Item no.:0610790
  • Total length: 113 mm
Item no.:0572854
  • Position: Outer
  • Inner splines: 25
  • Seal diameter: 60 mm
  • Outer splines: 38
  • ABS teeth: 45
Item no.:341310
  • Position: Front right, Inner
  • Inner splines: 28
  • Seal diameter: 50 mm
  • Total length: 300 mm
  • Joint diameter: 102 mm
Item no.:0339606
  • ABS teeth: 45
  • Inner diameter: 64 mm
  • Outer diameter: 74 mm
  • Width: 8,1 mm
Item no.:214620
  • Position: Front right
  • Splines wheel side: 26
  • Total length: 640 mm
  • Joint diameter: 90 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:219489
  • Position: Front right
  • Splines wheel side: 26
  • Total length: 640 mm
  • Diameter 1: 90 mm
  • ABS teeth: 45
Item no.:216077
  • Position: Front right
  • Splines wheel side: 26
  • Total length: 640 mm
  • Diameter 1: 90 mm
  • ABS teeth: 96
Item no.:113011
  • Position: Front left
  • Splines wheel side: 26
  • Total length: 693 mm
  • Joint diameter: 90 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:118964
  • Position: Front left
  • Splines wheel side: 26
  • Total length: 693 mm
  • Diameter 1: 90 mm
  • ABS teeth: 45
Item no.:117481
  • Position: Front left
  • Splines wheel side: 26
  • Total length: 693 mm
  • Diameter 1: 90 mm
  • ABS teeth: 96
Item no.:319865
  • Position: Front
  • Splines wheel side: 26
  • Total length: 660 mm
  • Joint diameter: 90 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:316746
  • Position: Front
  • Splines wheel side: 26
  • Total length: 660 mm
  • Joint diameter: 90 mm
  • ABS teeth: 96
Item no.:0137789
  • Splines wheel side: 38
  • Total length: 611 mm
  • Joint diameter: 90 mm
  • Joint diameter, gearbox side: 108 mm
  • ABS teeth: 45
Item no.:7303129
  • Position: Front
  • Splines wheel side: 38
  • Total length: 611 mm
  • Joint diameter: 90 mm
  • Joint diameter, gearbox side: 108 mm
Item no.:0679135
  • Total length: 122 mm
Item no.:0917712
  • Inner diameter: 24 mm
  • Outer diameter: 40 mm

Drivetrain for Audi 100 Avant 2.0 D

Maintaining the drivetrain on a classic such as the Audi 100 Avant 2.0 D requires both specialised knowledge and the correct components. As specialists in All car makes drivetrain and power transmission components, we supply a carefully chosen range tailored specifically for this model. This particular diesel variant places unique demands on its running gear, especially when handling the torque delivered by the engine. Choosing parts from a dedicated specialist ensures engine power reaches the wheels cleanly, without unnecessary power loss or mechanical failure.

We focus on supplying parts that not only fit physically, but also match the exact technical specifications for the Audi 100 Avant 2.0 D. Every detail matters, from the metallurgy in the CV joints to the durability of the CV boots protecting them. Sourcing your parts from us gives you access to genuine expertise, helping you keep your car in peak mechanical health whether you are carrying out preventative maintenance or an urgent repair.

How the drivetrain is configured on the Audi 100 Avant 2.0 D

The drivetrain of an Audi 100 Avant 2.0 D is a sturdy setup designed for durability and dependable service. The system uses a front-wheel-drive layout where power transfers from the longitudinally mounted diesel engine via the gearbox to the front wheels. Central to this setup are the drive shafts, fitted with both inner and outer CV joints. These constant velocity joints allow the wheels to move with suspension travel and steering angle while maintaining a constant rotational speed.

The inner CV joint mounts to the gearbox and accommodates the axial plunging movements created as the suspension works over bumps. The outer CV joint at the wheel hub is more complex, having to handle wide articulation angles at full steering lock. On an Audi 100 Avant 2.0 D, keeping these components in sound condition is vital to eliminate vibrations and ensure a smooth drive. The entire assembly is lubricated with high-grade grease retained by rubber CV boots, which serve as the first line of defence against road dirt and moisture.

Common faults and symptoms

There are several distinct signs that the drivetrain on your Audi 100 Avant 2.0 D is worn. One of the clearest symptoms of a worn outer CV joint is a rhythmic clicking or knocking sound on full steering lock, such as when turning into a parking space. This noise typically increases with vehicle speed and indicates that the joint's bearings have worn deep grooves into the raceways. Left unaddressed, the joint can eventually seize or break entirely.

Symptoms of a failing inner CV joint present differently. Wear here usually reveals itself as a pronounced shudder or vibration through the cabin during acceleration, especially at lower speeds or under heavy load. The CV boots are equally critical. If a boot tears, grease escapes rapidly and grit enters, destroying the joint in a very short distance. It pays to inspect the running gear on your Audi 100 Avant regularly to spot split rubber before expensive damage occurs.

Common parts to replace on the Audi 100 Avant 2.0 D

On the Audi 100 Avant 2.0 D, CV joints are the primary wear items after many years of faithful service. Depending on where the play or noise originates, you may need an inner or an outer replacement. We stock dedicated items for both positions to ensure a proper fit on your vehicle. The main components to check are:

  • Outer CV joint for Audi 100 Avant 2.0 D – The most frequent culprit when you hear clicking during tight turns.
  • Inner CV joint for Audi 100 Avant 2.0 D – The part to renew if you experience vibrations on acceleration.

Alongside the joints themselves, fitting fresh CV boots is good practice whenever the rubber shows signs of perishing, even if the joint is still sound. Replacing a boot proactively costs a fraction of fitting a complete replacement joint later. Our range includes complete boot kits supplied with grease, retaining clips and circlips, making fitting straightforward and reliable.

Finding the right parts for your Audi 100 Avant 2.0 D

Navigate to the relevant sub-category for your Audi 100 Avant 2.0 D:

With multiple potential drivetrain faults, starting in the precise sub-category saves time. Comparing the specific component categories for your Audi 100 Avant 2.0 D makes it simple to distinguish drive shaft, CV joint and propeller shaft issues, leading you straight to the right replacement part.

Finding the correct replacement parts for a classic Audi can occasionally be tricky due to running engineering changes across production years. To keep ordering simple and accurate, select your car's make, model, year and engine variant in our site navigation. This filters the catalogue down to verified components for your exact Audi 100 Avant 2.0 D, eliminating guesswork and avoiding ordering mistakes.

Once filtered, you can order with full confidence that engine details and transmission variants have been matched. If you need any technical advice before purchasing, our team of driveline specialists is on hand to help. We are dedicated to ensuring you find the right component first time, getting your classic Audi back on the road without unnecessary delay.

Why buy from CVJoint24?

CVJoint24 is more than just an online retailer; we are your dedicated partner for vehicle driveline and power transmission components. As an international shop backed by Swedish driveline specialists with a central warehouse in Helsingborg, Sweden, we combine an exhaustive inventory with deep technical know-how. We stock components for the Audi 100 Avant 2.0 D that standard motor factors often struggle to supply, always focusing on durable quality. Our mission is to supply the right part first time at a fair, competitive price.

We dispatch quickly across the European Union, keeping your car off axle stands and back where it belongs. You benefit from modern web ordering combined with the technical backing of a genuine specialist. Trust CVJoint24 for your Audi 100 Avant 2.0 D spare parts and experience the difference specialist knowledge makes.

Frequently Asked Questions about Drivetrain for Audi 100 Avant 2.0 D

How do I know whether the inner or outer CV joint is faulty?

If you hear a clicking noise while turning, it is usually the outer CV joint. If the car vibrates under acceleration, it is more likely that the inner CV joint is worn.

Do all CV joints fit every Audi 100 model?

No, there are differences depending on the engine and gearbox. Always select your car's make, model and engine on cvjoint24.com to find the exact replacement part for your 2.0 D.

Are grease and a CV boot included when I buy a CV joint from you?

Yes, our CV joint kits are normally supplied complete with a CV boot, specialised grease, clamps and fitting accessories for an easy replacement.

Can I replace the CV joint myself on my Audi 100 Avant 2.0 D?

Yes, it is achievable for a skilled DIY mechanic, but it requires the right tools and precision. Always remember to check the correct tightening torque for the hub bolt.

What happens if I continue driving with a damaged CV joint?

A damaged CV joint can eventually fail completely, causing the vehicle to lose drive entirely. It can also cause secondary damage to the wheel bearing and gearbox.

Do you offer a fitment guarantee?

Yes, when you choose your specific Audi 100 Avant 2.0 D model and engine, we guarantee that the part will fit, or we will help you exchange it for the correct one.