Audi Q2
Car parts and drivetrain components for Audi Q2.
Products for Audi Q2
- Position: Outer
- Seal diameter: 59 mm
- Inner splines: 27
- Outer splines: 36
- Joint diameter: 97,95 mm
- Position: Front right
- Total length: 817 mm
- Splines gearbox side: 40
- Splines wheel side: 36
- Position: Front left
- Flange diameter: 108 mm
- Total length: 523 mm
- Splines wheel side: 36
- Position: Front left
- Flange diameter: 110 mm
- Total length: 485 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 110 mm
- Total length: 767 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 119 mm
- Total length: 586 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 119 mm
- Total length: 575 mm
- Splines wheel side: 36
- Position: Rear right
- Flange diameter: 94 mm
- Total length: 650 mm
- Splines wheel side: 36
- Position: Front left
- Total length: 562 mm
- Splines gearbox side: 37
- Splines wheel side: 36
- Position: Front left, Inner
- Seal diameter: 31 mm
- Inner splines: 37
- Total length: 154 mm
- Splines gearbox side: 34
- Position: Front right, Inner
- Seal diameter: 41 mm
- Inner splines: 34
- Total length: 179 mm
- Splines gearbox side: 37
- Position: Rear, Outer
- Seal diameter: 59 mm
- Inner splines: 33
- Outer diameter: 82 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 119 mm
- Total length: 754 mm
- Splines wheel side: 36
- Position: Front right
- Total length: 789 mm
- Splines wheel side: 36
- Position: Inner
- Seal diameter: 100 mm
- Inner splines: 33
- Joint diameter: 100 mm
- Position: Rear left
- Flange diameter: 94 mm
- Total length: 611 mm
- Splines wheel side: 36
- Position: Rear
- Number of centre bearings: 1
- Number of joints: 1
- Total length: 2,176 mm
- Position: Front left
- Flange diameter: 108 mm
- Joint diameter: 108 mm
- Total length: 495 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 108 mm
- Joint diameter: 108 mm
- Total length: 795 mm
- Splines wheel side: 36
Frequently asked questions about Audi Q2 drivetrains
How do I know if my Audi Q2 needs a new drive shaft?
The most common symptoms are vibrations through the steering wheel or bodywork during acceleration, as well as noises such as clicking or knocking sounds while driving.
What is the difference between the inner and outer CV joint on an Audi Q2?
The outer CV joint sits next to the wheel and typically causes clicking noises when cornering. The inner CV joint is located by the gearbox and usually creates vibrations under acceleration and load.
Do all drive shafts fit all Audi Q2 models?
No, drive shafts differ depending on whether the car has a manual or automatic gearbox, as well as whether it is front-wheel drive or Quattro. Always select your make, model and engine to find the correct part.
Are the CV boot and grease included when I buy a CV joint for my Q2?
Yes, our CV joints are supplied as complete kits containing the CV joint, CV boot, grease, clamps and fitting bolt or nut.
How does a split CV boot affect the drivetrain on my Audi Q2?
A split CV boot allows the lubricating grease to leak out and dirt to enter the joint, which quickly causes severe wear and ultimately joint failure.
Do you stock propeller shafts for the Audi Q2?
Yes, we have propeller shafts available for Audi Q2 models equipped with all-wheel drive (Quattro).