Audi Q2 2.0 TDI Quattro
Car parts and drivetrain components for Audi Q2 2.0 TDI Quattro. Always check the fit before ordering.
Products for Audi Q2 2.0 TDI Quattro
- Position: Front right
- Flange diameter: 119 mm
- Total length: 586 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 119 mm
- Total length: 575 mm
- Splines wheel side: 36
- Position: Rear right
- Flange diameter: 94 mm
- Total length: 650 mm
- Splines wheel side: 36
- Position: Front left
- Total length: 562 mm
- Splines gearbox side: 37
- Splines wheel side: 36
- Position: Front left, Inner
- Seal diameter: 31 mm
- Inner splines: 37
- Total length: 154 mm
- Splines gearbox side: 34
- Position: Front right, Inner
- Seal diameter: 41 mm
- Inner splines: 34
- Total length: 179 mm
- Splines gearbox side: 37
- Position: Rear, Outer
- Seal diameter: 59 mm
- Inner splines: 33
- Outer diameter: 82 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 119 mm
- Total length: 754 mm
- Splines wheel side: 36
- Position: Rear
- Number of centre bearings: 1
- Number of joints: 1
- Total length: 2,176 mm
- Position: Inner
- Seal diameter: 94 mm
- Inner splines: 33
- Number of joints: 3
- ABS teeth: 0
- Position: Front left
- Flange diameter: 100 mm
- Total length: 524 mm
- Splines wheel side: 36
- Position: Front right
- Flange diameter: 100 mm
- Total length: 815 mm
- Splines wheel side: 36
- Position: Rear left
- Diameter: 94 mm
- Flange diameter: 94 mm
- Total length: 611 mm
- ABS teeth: 0
- Position: Rear, Outer
- Seal diameter: 59,5 mm
- Inner splines: 33
- Total length: 80 mm
- Splines gearbox side: 36
- Position: Front right
- Flange diameter: 119 mm
- Total length: 760 mm
- Splines wheel side: 36
- Position: Rear
- Number of joints: 1
- Total length: 2,176 mm
Frequently asked questions about drivetrain parts for Audi Q2 2.0 TDI Quattro
How do I know whether the inner or outer CV joint is faulty on my Audi Q2 Quattro?
Generally, a worn outer CV joint produces a clicking or knocking noise on full steering lock while driving. A worn inner CV joint tends to cause vibrations through the car's body, particularly under hard acceleration, whether you are turning or driving straight ahead.
Will drive shafts from a front-wheel-drive Audi Q2 fit my 2.0 TDI Quattro?
No, the drive shafts often differ between front-wheel-drive models and Quattro models due to differences in the gearbox, differential, and suspension. Always select your vehicle by make, model, and engine variant to ensure you get the correct shaft for your Quattro.
Why is it important to replace a split CV boot promptly on an Audi Q2?
The CV boot protects the constant velocity joint from dirt, water, and road salt while keeping the lubricating grease in place. If the boot splits, the joint will rapidly degrade due to contamination, leading to a far more expensive replacement of the complete CV joint or drive shaft.
Do your drive shafts for Audi Q2 2.0 TDI Quattro come with everything needed for fitting?
Yes, our complete drive shafts are supplied fully assembled with inner and outer joints, CV boots, and grease. In most cases, essential fitting hardware such as the centre hub bolt or nuts is also included.
How does the Quattro system affect wear on the drivetrain?
Because power is distributed across all four wheels, the strain on the individual front driveshafts is reduced compared to a two-wheel-drive car. However, the system includes additional moving components, such as the propeller shaft and rear drive shafts, which require inspection and maintenance.
Can I replace just the inner CV joint on my Audi Q2 2.0 TDI Quattro?
Yes, provided the drive shaft itself is straight and undamaged, you can replace just the inner CV joint. We supply individual inner CV joints tailored specifically for the 2.0 TDI Quattro model to provide a more cost-effective repair.