Drive shafts for Mitsubishi Lancer

Find the right drive shaft for your Mitsubishi Lancer, whether you drive an early saloon from the late 1980s or a later model with a FlexFuel engine. Our range covers both front-wheel...

Products for Drive shafts for Mitsubishi Lancer

34 products
1 - 24 of 34
Item no.:2125168
  • Position: Front right
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 939 mm
  • ABS teeth: 43
Item no.:1162983
  • Position: Front left
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 616 mm
  • ABS teeth: 43
Item no.:215662
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 25
  • Total length: 940 mm
  • ABS teeth: 43
Item no.:113504
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 25
  • Total length: 617 mm
  • ABS teeth: 43
Item no.:1138923
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 27
  • Total length: 560 mm
  • ABS teeth: 43
Item no.:2118350
  • Position: Front right
  • Splines gearbox side: 24
  • Splines wheel side: 27
  • Total length: 640 mm
  • ABS teeth: 43
Item no.:1104058
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 650 mm
  • Diameter 1: 83 mm
Item no.:2191628
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 970 mm
  • Joint diameter: 83 mm
Item no.:1176935
  • Position: Front left
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 933 mm
  • Joint diameter: 80 mm
Item no.:2190905
  • Position: Front right
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 591 mm
  • Joint diameter: 77 mm
Item no.:416969
  • Position: Rear left
  • Splines gearbox side: 27
  • Splines wheel side: 27
  • Total length: 675 mm
Item no.:517525
  • Position: Rear right
  • Splines gearbox side: 26
  • Splines wheel side: 27
  • Total length: 663 mm
Item no.:315621
  • Total length: 53 mm
Item no.:1179461
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 28
  • Total length: 630 mm
  • Joint diameter: 95 mm
Item no.:1147769
  • Position: Front left
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 616 mm
  • ABS teeth: 43
Item no.:215163
  • Position: Front right
  • Splines gearbox side: 25
  • Splines wheel side: 28
  • Total length: 945 mm
Item no.:2108641
  • Position: Front right
  • Splines gearbox side: 26
  • Splines wheel side: 27
  • Total length: 638 mm
  • ABS teeth: 43
Item no.:1159898
  • Position: Front left
  • Splines gearbox side: 26
  • Splines wheel side: 27
  • Total length: 560 mm
  • ABS teeth: 43
Item no.:212682
  • Position: Front right
  • Splines gearbox side: 24
  • Splines wheel side: 27
  • Total length: 562 mm
  • ABS teeth: 43
Item no.:119510
  • Position: Front left
  • Splines gearbox side: 24
  • Splines wheel side: 27
  • Total length: 642 mm
  • ABS teeth: 43
Item no.:1174370
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 650 mm
Item no.:1124101
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 615 mm
  • ABS teeth: 43
Item no.:2131688
  • Position: Front right
  • Splines gearbox side: 25
  • Splines wheel side: 25
  • Total length: 596 mm
  • Diameter 1: 80 mm
Item no.:1146847
  • Position: Front left
  • Splines wheel side: 25
  • Total length: 923 mm
  • Joint diameter: 82 mm
Showing 1–24 of 34 products

Drive shafts for Mitsubishi Lancer

The drive shaft is a vital component in your Mitsubishi Lancer drivetrain that is easily overlooked until problems arise. It is responsible for transferring torque from the gearbox directly to the road wheels, driving the car forward under load. Here at CVJoint24 you will find a range of drive shafts tailored for various Lancer generations. Our selection covers a broad spectrum of needs, from everyday standard models to more demanding specifications. Choosing a high-quality drive shaft is essential for preserving your car's handling, keeping vibrations to a minimum and ensuring total safety in all driving conditions on European roads.

What does a drive shaft do on a Mitsubishi Lancer?

On a Mitsubishi Lancer, the drive shaft acts as the primary connection between the engine's power and the road. It generally consists of a sturdy shaft bar fitted with an inner and an outer CV joint, both protected by rubber CV boots. The inner joint connects to the gearbox and allows the shaft to move plunge-wise as the suspension travels up and down. The outer joint sits at the wheel hub and is engineered to accommodate steering angles whilst continuously transmitting torque. Working together, these components ensure that power delivery remains smooth and uninterrupted, whether accelerating hard in a straight line or cornering through tight bends.

Common signs of wear

There are several distinct symptoms indicating that a drive shaft on your Mitsubishi Lancer is approaching the end of its service life. One of the most typical signs is a rhythmic clicking or knocking noise clearly audible when taking tight turns at low speeds, which usually points to a worn outer joint. If you instead experience noticeable vibrations through the steering wheel or chassis under acceleration, the inner joint may have developed excessive play. It is also crucial to inspect the CV boots regularly; if they are split, lubricating grease escapes while grit and water enter, quickly resulting in complete and costly joint failure.

How to choose the correct drive shaft

Finding the right drive shaft for your specific Mitsubishi Lancer requires careful checking, as technical specifications vary substantially across model years and engine variants. Crucial differences exist depending on whether the car has a manual or automatic gearbox, and whether it features ABS brakes. The spline count on the shaft ends and the total overall length must match precisely for proper fitment. To eliminate uncertainty and avoid purchasing the wrong part, simply select your Mitsubishi Lancer's make, model and engine variant in our store. This filters our catalogue so you only see the driveshafts engineered for your exact configuration.

Related parts to check

It is good practice to check these related pages for the same vehicle when working on the drive shaft:

When one drivetrain component shows signs of wear, nearby parts on the vehicle often require inspection too. By comparing these related pages for the Mitsubishi Lancer, it becomes simpler to determine whether an issue stems strictly from the drive shaft or from another neighbouring part of the drivetrain.

This is especially important on models where vibrations, play and unusual noises can transfer symptoms across several driveline components. Checking related categories helps avoid replacing the correct component type while overlooking an adjacent worn part that contributes to the very same problem.

Another key component is the car's ABS ring, which is frequently fitted directly onto the outer CV joint or drive shaft itself. If the ring is cracked or heavily corroded, it can send inaccurate signals to your vehicle's safety systems. Checking and renewing these related parts at the same time will save you both time and future labour costs.

Why buy from CVJoint24?

CVJoint24 is the international shop of a Swedish specialist in All car makes drivetrains, shipping directly from our warehouse in Helsingborg, Sweden. We combine in-depth technical expertise with a product range engineered to high standards to meet the demands of modern vehicles. When you order a drive shaft for your Mitsubishi Lancer from us, you can be confident of an accurate fit and long-term durability. Because we specialise in driveline components, we provide the dedicated product knowledge and technical support that general car parts stores rarely match. With straightforward selection by make, model and engine, reliable fitment and fast shipping across the EU, we are the trusted choice for Lancer owners.

Frequently Asked Questions about Drive Shafts for Mitsubishi Lancer

How do I know if my Mitsubishi Lancer needs a new drive shaft?

The most common symptoms are clicking noises when turning, vibrations under acceleration, or visible damage to the drive shaft boots where grease has leaked out.

Can I replace just the CV joint instead of the entire drive shaft?

Yes, on many Mitsubishi Lancer models you can replace just the outer or inner CV joint if the shaft itself is undamaged, which can often be a more economical alternative.

Is there a difference between drive shafts for manual and automatic gearboxes?

Yes, there are often differences in both length and mounting splines between manual and automatic gearboxes, so always select your car's exact model and engine to find the correct part.

Why is my Mitsubishi Lancer vibrating under acceleration?

Vibrations under acceleration are often caused by wear in the inner CV joint, creating an imbalance in the drive shaft when put under load.

Are boots and grease included when I buy a complete drive shaft?

Yes, when you buy a complete drive shaft from us, it comes fully assembled with new boots, joints, and the correct amount of grease, ready for installation.

How long does it take to replace a drive shaft?

For an experienced mechanic, it typically takes between 1 and 2 hours per side, depending on the car's condition and whether any bolts are seized due to corrosion.