Audi A4 Allroad
Car parts and drivetrain components for Audi A4 Allroad.
Products for Audi A4 Allroad
- Position: Outer
- Seal diameter: 76,5 mm
- Inner splines: 25
- Outer splines: 42
- Position: Front, Outer
- Inner splines: 28
- Outer diameter: 94 mm
- Splines wheel side: 42
- Position: Front left, Front right
- Flange diameter: 123 mm
- Total length: 469 mm
- Splines wheel side: 42
- Position: Rear left, Rear right
- Flange diameter: 100 mm
- Total length: 626 mm
- Splines wheel side: 42
- Position: Rear
- Number of centre bearings: 1
- Number of joints: 2
- Total length: 1,630 mm
- Position: Rear left
- Total length: 587 mm
- Splines wheel side: 42
- Position: Rear right
- Total length: 545 mm
- Splines wheel side: 42
- Number of centre bearings: 1
- Number of joints: 2
- Total length: 1,529 mm
- Position: Rear
- Number of centre bearings: 1
- Number of joints: 3
- Total length: 1,640 mm
- Position: Rear left, Rear right
- Flange diameter: 100 mm
- Total length: 630 mm
- Splines wheel side: 42
- Position: Outer
- Seal diameter: 76,5 mm
- Inner splines: 33
- Outer splines: 42
- Joint diameter: 88 mm
- Position: Rear left, Rear right
- Flange diameter: 108 mm
- Total length: 632 mm
- Splines wheel side: 42
- Position: Outer
- Seal diameter: 76 mm
- Inner splines: 27
- Outer splines: 42
- Joint diameter: 100 mm
- Position: Front, Outer
- Inner splines: 25
- Outer diameter: 85 mm
- Splines wheel side: 42
- Diameter: 30 mm
- Height: 102 mm
- Hole spacing c/c: 228 mm
- Inner diameter: 30 mm
- Bearing thickness: 15 mm
- Position: Inner
- Inner splines: 28
- Outer diameter: 108 mm
Frequently Asked Questions about Drivetrain for Audi A4 Allroad
How do I know if my Audi A4 Allroad needs a new drive shaft?
The most common signs are vibrations under acceleration or noises when cornering. If you notice the car shaking at certain speeds or a clunking noise when driving over bumps, you should inspect the drive shafts.
Are the drive shafts on the Audi A4 Allroad different from standard estate models?
Yes, the Audi A4 Allroad often features specific drive shafts due to its raised ground clearance and wider track. It is therefore essential to select your exact model and engine variant to find the correct part.
What causes a clicking noise on full steering lock?
This is almost always caused by a worn outer CV joint. When excessive play develops around the steel balls inside the joint due to wear, it produces that characteristic clicking noise while driving at an angle.
Can I replace just the CV joint instead of the entire drive shaft?
Yes, on most Audi A4 Allroad models you can replace just the inner or outer CV joint. This is a cost-effective alternative if the shaft itself is undamaged.
Why does my Audi A4 Allroad vibrate at higher speeds?
Vibrations felt throughout the vehicle at motorway speeds can often be traced to the propeller shaft or its centre bearing. They can also stem from wear in the inner CV joints.
How often should I check the CV boots on my Audi A4 Allroad?
We recommend a visual inspection at every service or seasonal tyre change. An intact CV boot is the best defence against costly damage to your constant velocity joints.
Are grease and fitting accessories included when I buy a CV joint?
Yes, when you purchase a CV joint from us, it normally comes complete with the correct grease, a CV boot and the necessary clamps for a full installation.