Audi A6 2.4 Quattro
Car parts and drivetrain components for Audi A6 2.4 Quattro. Always check the fit before ordering.
Products for Audi A6 2.4 Quattro
- Position: Front right
- Flange diameter: 130 mm
- Total length: 550 mm
- Splines wheel side: 38
- ABS teeth: 45
- Position: Front left
- Flange diameter: 130 mm
- Total length: 625 mm
- Splines wheel side: 38
- ABS teeth: 45
- Position: Front right
- Flange diameter: 130 mm
- Total length: 524 mm
- Splines wheel side: 38
- ABS teeth: 45
- Position: Front right
- Flange diameter: 130 mm
- Total length: 643 mm
- Splines wheel side: 38
- ABS teeth: 45
- Diameter: 30 mm
- Height: 105 mm
- Hole spacing c/c: 241 mm
- Bearing thickness: 15 mm
- Diameter: 30 mm
- Height: 82 mm
- Hole spacing c/c: 241 mm
- Bearing thickness: 13 mm
- Position: Outer
- ABS teeth: 45
- Seal diameter: 59 mm
- Inner splines: 27
- Outer splines: 38
- Position: Rear
- Number of centre bearings: 1
- Number of joints: 3
- Total length: 1,755 mm
- Position: Front
- ABS teeth: 45
- Inner diameter: 77 mm
- Outer diameter: 81 mm
- Width: 11 mm
- Position: Front left, Front right
- Flange diameter: 123 mm
- Joint diameter: 123 mm
- Total length: 544 mm
- ABS teeth: 45
- Position: Rear
- Diameter: 94 mm
- Total length: 655 mm
- Splines wheel side: 38
- ABS teeth: 45
- Position: Front left
- Flange diameter: 123 mm
- Total length: 605 mm
- Splines wheel side: 38
- Position: Front left
- Total length: 617 mm
- Splines wheel side: 38
- Position: Front right
- Flange diameter: 123 mm
- Total length: 525 mm
- Splines wheel side: 38
- Position: Front right
- Flange diameter: 123 mm
- Total length: 655 mm
- Splines wheel side: 38
- Position: Rear left, Rear right
- Flange diameter: 108 mm
- Total length: 650 mm
- Splines wheel side: 38
- Position: Outer
- Seal diameter: 59 mm
- Inner splines: 27
- Outer splines: 38
- Joint diameter: 100 mm
Frequently Asked Questions about Drivetrain Parts for Audi A6 2.4 Quattro
How do I know if my Audi A6 2.4 Quattro needs a new drive shaft?
The most common signs are vibrations under acceleration or unusual noises when cornering. If the CV boot is split and grease has leaked out over a long period, there is a high risk that the complete drive shaft must be replaced to ensure reliability.
Does the same CV joint fit both the front and rear axles on a Quattro?
No, the CV joints usually differ between the front and rear axles on the Audi A6 2.4 Quattro. It is therefore essential to select your car's exact model, year and engine, and verify the fitting position (front/rear) before ordering.
Why does my Audi A6 vibrate during acceleration?
Vibrations under acceleration are often caused by wear in the inner CV joints. On a Quattro model, it can also stem from an unbalanced propeller shaft or worn centre bearings. Check these components if the vibrations persist.
Is it difficult to replace an ABS ring on an Audi A6?
It requires removing the CV joint from the wheel hub. Once the joint is detached, the old ring can be tapped off and the new one pressed or heat-fitted into place. This is a common procedure to resolve ABS fault codes.
What is included when I buy a complete drive shaft from you?
Our complete drive shafts are supplied fully assembled with inner and outer CV joints, boots, grease, and the necessary fittings such as bolts or nuts, so you can install the part straight away.
How often does the propeller shaft on a Quattro need servicing?
The propeller shaft is generally maintenance-free, but you should regularly inspect the centre bearing and universal joints for play or cracked rubber, especially on high-mileage cars or vehicles driven in harsh climates.