BMW 4 Serie

Spare parts and drivetrain components for BMW 4 Serie.

Choose version

Choose a version to refine the results and get closer to the right product.

Products for BMW 4 Serie

1,064 products
97 - 120 of 1064
Item no.:1170230
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 37
  • Total length: 557 mm
Item no.:2105854
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 37
  • Total length: 857 mm
Item no.:626828
  • Position: Rear
Item no.:4156203
  • Position: Rear left
  • Splines gearbox side: 32
  • Splines wheel side: 30
  • Total length: 755 mm
Item no.:5185650
  • Position: Rear right
  • Splines gearbox side: 32
  • Splines wheel side: 30
  • Total length: 834 mm
Item no.:7316272
  • Position: Rear
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 750 mm
Item no.:6219110
  • Position: Rear
  • Total length: 1,492 mm
  • Number of joints: 3
  • Outer diameter 1: 14 mm
  • Bolt circle diameter 1: 96 mm
Item no.:7316267
  • Position: Rear left
  • Splines gearbox side: 27
  • Splines wheel side: 28
  • Total length: 751 mm
  • Joint diameter: 84 mm
Item no.:6237761
  • Position: Rear
  • Total length: 1,330 mm
  • Number of joints: 1
  • Number of centre bearings: 1
Item no.:4157775
  • Position: Rear left
  • Splines gearbox side: 27
  • Splines wheel side: 37
  • Total length: 700 mm
Item no.:5160188
  • Position: Rear right
  • Splines gearbox side: 27
  • Splines wheel side: 37
  • Total length: 756 mm
Item no.:7285254
  • Position: Rear
  • Total length: 1,408 mm
  • Number of joints: 3
  • Outer diameter 1: 14 mm
  • Bolt circle diameter 1: 105 mm
Item no.:625285
  • Position: Rear
  • Total length: 1,548 mm
  • Outer diameter 1: 14 mm
  • Bolt circle diameter 1: 96 mm
  • Outer diameter 2: 16 mm
Item no.:0806071
  • Inner diameter: 30 mm
  • Bearing thickness: 36 mm
  • Hole spacing c/c: 160 mm
  • Height: 54 mm
Item no.:6504716
  • Position: Outer
  • Inner splines: 25
  • Splines wheel side: 28
  • Outer diameter: 90 mm
Item no.:0942163
  • Inner diameter: 43 mm
  • Outer diameter: 90 mm
Item no.:694358
  • Position: Rear
Item no.:1153112
  • Position: Front left
  • Splines gearbox side: 27
  • Splines wheel side: 37
  • Total length: 555 mm
Item no.:2117265
  • Position: Front right
  • Splines gearbox side: 27
  • Splines wheel side: 37
  • Total length: 855 mm
Item no.:353063
  • Position: Front, Outer
  • Inner splines: 33
  • Seal diameter: 56 mm
  • Outer splines: 31
  • Thread size: M16X1,5X72
Item no.:621510
  • Position: Rear
  • Total length: 1,266 mm
  • Outer diameter 1: 14 mm
  • Bolt circle diameter 1: 105 mm
  • Outer diameter 2: 16 mm
Item no.:0580111
  • Position: Outer
  • Inner splines: 33
  • Splines wheel side: 31
  • Outer diameter: 86 mm
Showing 97–120 of 1064 products

Drivetrain for BMW 4 Serie

The BMW 4 Serie represents a perfect balance between striking aesthetics and dynamic performance. Maintaining this balance demands a drivetrain capable of handling the substantial torque and forces generated by the engine. The drivetrain is the core of your vehicle's power transmission, consisting of several critical components that work in unison to transfer power from the gearbox to the road wheels. Here at CVJoint24, you will find a dedicated range tailored specifically to this model series. We understand the precise technical demands of a modern BMW, which is why we supply only parts that match or exceed original specifications.

Our range covers everything from circlips and fasteners to complete shafts. Catering comprehensively for the BMW 4 Serie, we meet virtually every requirement, whether for an entry-level specification or a high-performance engine variant. Maintaining the drivetrain is vital not only for long-term reliability, but also for preserving the sharp steering response and immediate acceleration that define the marque. Choosing the correct replacement components helps prevent consequential damage to surrounding suspension and transmission assemblies.

How the BMW 4 Serie drivetrain is engineered

The drivetrain layout on the BMW 4 Serie varies depending on whether the car is rear-wheel drive (RWD) or equipped with the intelligent xDrive all-wheel-drive system. At its foundation, power is transmitted longitudinally via a propeller shaft running to the rear differential. On xDrive models, a transfer case and a front prop shaft route torque forward to the front differential, where two additional drive shafts power the wheels. This intricate setup requires every component—such as the propeller shaft for BMW 4 Serie—to function smoothly to eliminate unwanted vibrations and drivetrain drag.

Each drive shaft uses two constant velocity joints: an inner CV joint and an outer CV joint. The inner joint mounts nearest to the differential or gearbox, accommodating axial plunge as the suspension moves over road undulations. The outer joint sits at the wheel hub, allowing for articulation during steering while smoothly transferring rotational drive. On the BMW 4 Serie, these assemblies are engineered to withstand heavy operational loads, yet they remain vulnerable to wear caused by heat, grit, and physical stress. Understanding this setup is essential when diagnosing symptoms or selecting the right car parts for a repair.

Common faults and symptoms

Several clear symptoms point to drivetrain wear on a BMW 4 Serie. One of the most typical signs is a distinct clicking or knocking noise on tight turns at low speeds. This usually indicates that an outer CV joint for BMW 4 Serie is worn, or that road grit has penetrated through a torn CV boot. If you instead experience a shudder or vibration through the cabin under hard acceleration, the fault can often be traced to a worn inner CV joint for BMW 4 Serie or an unbalanced propeller shaft.

Perished or split drive shaft boots are another frequent problem. When grease escapes, lubrication is lost rapidly, resulting in dry metal-on-metal friction and sudden joint failure. You should also watch for harmonic vibrations appearing at specific road speeds, which typically point to a failing prop shaft centre bearing or thrown balance weights. Addressing these warnings early often allows you to replace just a single CV joint or CV joint boot before the entire driveshaft suffers permanent damage.

Popular replacement parts for BMW 4 Serie

Depending on your driving style and mileage, certain components see heavier service demands than others. In our BMW 4 Serie catalogue, our most sought-after categories include:

  • Drive shafts (163 items): The most common replacement when experiencing extensive joint wear or shaft damage.
  • Propeller shafts (60 items): Critical for driveline torque transfer between front and rear axles, especially on xDrive variants.
  • Outer CV joints (41 items): Frequently replaced due to severe operating angles and exposure to road debris at the wheel end.
  • Inner CV joints (28 items): Typically renewed when experiencing driveline vibrations under load.

Choosing a complete drive shaft for BMW 4 Serie is often the most cost-effective solution compared to rebuilding individual joints. You receive a fully assembled, factory-balanced unit pre-packed with fresh grease and fitted with new boots. This significantly cuts workshop fitting time and ensures dependable longevity. We also stock specific fitting hardware, such as hub bolts and retaining rings, to ensure a professional repair.

How to find the correct parts for BMW 4 Serie

Navigate directly to the relevant category for your BMW 4 Serie:

When diagnosing drivetrain issues, pinpointing the correct subcategory straight away saves valuable time. By comparing the specific sections for the BMW 4 Serie, you can easily distinguish between drive shaft, CV joint, or prop shaft faults and browse the components that match your car's symptoms and specification.

Our experienced customer support team is always on hand to provide technical advice if you require guidance regarding fitment or component selection.

Why buy from CVJoint24?

CVJoint24 is an international shop backed by a Swedish driveline specialist, operating with dedicated warehouse facilities in Helsingborg, Sweden. By focusing strictly on driveline and transmission components, we offer a level of technical depth and product availability that general motor factors struggle to match. For your BMW 4 Serie, this means access to parts engineered to rigorous standards for an exact fit and OE-level durability. We recognise how important it is to keep your vehicle on the road, supported by efficient dispatch across the European Union.

Ordering from us means buying with confidence from specialists who know drivelines inside and out. We pair deep technical knowledge with an intuitive website where you can quickly find compatible parts by selecting your vehicle's make, model, and engine variant. With extensive coverage for the BMW 4 Serie, CVJoint24 is the trusted supplier for both DIY mechanics and independent garages demanding premium quality and engineering precision.

Frequently Asked Questions about BMW 4 Series Drivetrain Parts

How do I know if my BMW 4 Series needs a new drive shaft?

The most common signs are vibrations under acceleration, clicking noises when cornering, or visible grease leaking from the CV boots. If you notice an imbalance at higher speeds, this can also indicate a damaged drive shaft.

Does the same drive shaft fit both rear-wheel drive and xDrive models?

No, drive shafts differ between rear-wheel drive and xDrive versions. In addition, xDrive models have front drive shafts, which RWD models do not have. Always select your vehicle's make, model, and engine variant to ensure you receive the correct version.

Can I replace just the CV joint instead of the complete drive shaft?

Yes, if the shaft itself is straight and undamaged, you can often replace just the outer or inner CV joint. This is a cost-effective way to repair the drivetrain if the fault is confined to the joint itself.

What causes propeller shaft vibrations on a BMW 4 Series?

Propeller shaft vibrations are commonly caused by a worn centre bearing, deteriorated flexible coupling discs (guibo), or an unbalanced prop shaft. It is vital to resolve this quickly to prevent damage to the gearbox or differential.

Is it difficult to replace a CV boot yourself?

It requires specific tools and mechanical experience, as the drive shaft usually needs to be removed from the hub. However, it is an essential preventative maintenance task to avoid more costly constant velocity joint repairs.

How many drive shafts does a BMW 4 Series xDrive have?

A BMW 4 Series with xDrive has four drive shafts in total: two at the front and two at the rear, in addition to the propeller shafts that distribute power between the axles.

Why should I choose CVJoint24 for my BMW parts?

We are Swedish driveline specialists with an extensive range of premium products. We provide guaranteed fitment when you select your vehicle's model details, offering parts that are technically verified for your BMW 4 Series.