Inner CV joints for Fiat

Find the right inner CV joint for your Fiat, whether you drive a nimble hatchback or a spacious van. Our range covers components for both petrol and diesel engines across models from...

Choose model

Choose a model to move to more precise products and the next step in the vehicle tree.

Products for Inner CV joints for Fiat

336 products
121 - 144 of 336
Item no.:340913
  • Position: Front, Inner
  • Inner splines: 22
  • Seal diameter: 36 mm
  • Total length: 155 mm
  • Outer splines: 22
Item no.:647003
  • Position: Rear, Inner
  • Inner splines: 21
  • Total length: 88 mm
Item no.:347212
  • Position: Front, Inner
  • Inner splines: 20
  • Outer splines: 22
Item no.:342416
  • Position: Front, Inner
  • Inner splines: 25
  • Splines gearbox side: 25
  • Total length: 32 mm
Item no.:340778
  • Position: Front, Inner
  • Inner splines: 24
  • Splines gearbox side: 24
  • Seal diameter: 29,7 mm
  • Total length: 493 mm
Item no.:0429944
  • Position: Front left, Inner
  • Inner splines: 26
  • Seal diameter: 32 mm
  • Outer splines: 25
Item no.:0428176
  • Position: Front, Inner
  • Inner splines: 22
  • Outer diameter: 84 mm
  • Splines wheel side: 22
Item no.:3460318
  • Position: Inner
  • Inner splines: 20
  • Outer diameter: 69 mm
Item no.:348932
  • Position: Front, Inner
  • Inner splines: 19
  • Splines gearbox side: 22
  • Seal diameter: 36 mm
  • Total length: 150 mm
Item no.:246454
  • Position: Front right, Inner
  • Inner splines: 24
  • Splines gearbox side: 24
  • Seal diameter: 29,7 mm
  • Total length: 479,5 mm
Item no.:244067
  • Position: Inner
  • Inner splines: 33
  • Splines gearbox side: 26
Item no.:140200
  • Position: Inner
  • Inner splines: 33
  • Splines gearbox side: 28
Item no.:0475804
  • Position: Inner
  • Inner splines: 23
  • Splines gearbox side: 25
  • Seal diameter: 35 mm
  • Outer splines: 25
Item no.:341621
  • Position: Front, Inner
  • Inner splines: 34
  • Total length: 47,5 mm
  • Joint diameter: 108 mm
Item no.:246182
  • Position: Front right, Inner
  • Inner splines: 26
  • Splines gearbox side: 25
  • Seal diameter: 29,8 mm
  • Total length: 485 mm
Item no.:145547
  • Position: Front left, Inner
  • Inner splines: 24
  • Splines gearbox side: 34
  • Seal diameter: 35 mm
  • Total length: 171,5 mm
Item no.:245641
  • Position: Front right, Inner
  • Inner splines: 22
  • Splines gearbox side: 22
  • Seal diameter: 43,1 mm
  • Total length: 195,5 mm
Item no.:249704
  • Position: Inner
  • Splines gearbox side: 41
  • Splines wheel side: 29
  • Tripod shaft diameter: 42 mm
Item no.:246866
  • Position: Front right, Inner
  • Inner splines: 26
  • Splines gearbox side: 25
  • Seal diameter: 29,7 mm
  • Total length: 542 mm
Item no.:149731
  • Position: Inner
  • Inner splines: 26
  • Seal diameter: 32 mm
  • Total length: 168 mm
  • Outer splines: 25
Item no.:147502
  • Position: Inner
  • Inner splines: 27
  • Splines gearbox side: 39
Item no.:241139
  • Position: Inner
  • Inner splines: 27
  • Splines gearbox side: 39
  • Total length: 460 mm
Item no.:348410
  • Position: Inner
  • Inner splines: 25
  • Joint diameter: 100 mm
Item no.:0418535
  • Position: Front right, Inner
  • Inner splines: 23
  • Outer splines: 25
Showing 121–144 of 336 products

Inner CV joints for Fiat

The inner CV joint is a fundamental part of your Fiat's drivetrain system. Unlike the outer CV joint, which sits by the wheel hub and accommodates large steering angles, the inner CV joint is mounted directly to the gearbox or differential. Its primary job is to transfer engine torque to the drive shaft whilst allowing the shaft to plunge in and out as the suspension moves. For a Fiat, whether it is a compact city hatchback or a larger commercial van, this flexibility is crucial for maintaining smooth power delivery without causing mechanical strain in the drivetrain.

A sound inner CV joint ensures that your car rolls smoothly and that vibrations are kept to a minimum, protecting both the gearbox and wheel bearings. The inner constant velocity joint operates under continuous stress and relies on dedicated high-performance grease to withstand the heat generated at higher speeds. Over the decades, Fiat has engineered its drivetrains to be both efficient and durable, but like all moving car parts, they require maintenance and eventual replacement to preserve factory handling. Here you will find a carefully selected range meeting the rigorous demands placed on modern spare parts.

How inner CV joints differ across Fiat models

Fiat has implemented various technical designs for its inner CV joints over the years, making it vital to know exactly what is fitted to your specific model. Many smaller Fiat models utilise a tripod joint (three-point star), renowned for efficiently accommodating axial plunge in the drivetrain. Larger models or variants with higher torque outputs may instead use ball-type designs similar to outer joints, yet with an integrated sliding mechanism. Differences also extend to the number of splines on the shaft and the overall joint diameter.

A drive shaft can feature different mountings depending on whether your car has a manual or automatic gearbox, alongside its engine output. From the 1990s onward, significant standardisation took place across the Fiat Group, yet noticeable variations remain between an urban runabout and a vehicle built for commercial payload. Checking the original equipment (OE) number is often a practical approach to verify that the inner CV joint matches the gearbox output shaft precisely. While various models occasionally share components, fitment is frequently specific to the exact engine and gearbox combination.

Common signs of wear

Wear in an inner CV joint typically presents differently than in an outer unit. The most classic symptom is vibration through the entire vehicle under acceleration, particularly at speeds between 50 and 90 km/h. These vibrations can be felt through the steering wheel, but they are often experienced as a lateral shudder across the entire car body. When you lift off the accelerator, the shaking usually subsides, clearly indicating that the issue lies in the inner joint rather than wheel balancing. Another frequent sign is grease leaking from the CV boots. If a boot tears, grease is flung out while road dirt and moisture penetrate the joint.

This rapidly causes increased friction and heat build-up, damaging the hardened bearing surfaces inside. A dull clunking noise under acceleration or engine braking can also signal internal play within the joint mechanism. Leaving these vibrations unchecked can cause the gearbox output seals to fail, potentially leading to differential damage. It is wise to inspect the condition of your drive shaft boots during every routine service or tyre change to catch small splits before they require a complete joint replacement.

Choosing the right inner CV joint for your Fiat

Selecting the correct inner CV joint for your Fiat is straightforward when using the right details. Because Fiat has frequently introduced running technical updates over a model's lifecycle, the year of manufacture alone may not be enough. The most reliable method is to select your vehicle's exact make, model and engine variant in our store. This filters our catalogue down to parts engineered to match your car's technical specification. If multiple options are listed for your vehicle, check key technical data such as the inner and outer spline counts and overall dimensions.

Where possible, inspecting your existing joint beforehand to confirm whether it is a tripod joint or a ball-and-cage type is also helpful. During replacement, it is sensible to evaluate surrounding components as well. Do you require a replacement ABS ring, or is it time for fresh gearbox oil? Choosing carefully ensures you receive a component backed by our fitment guarantee that will perform reliably for many kilometres to come. Getting the correct part straight away saves workshop time and avoids inconvenient returns.

Popular Fiat models to explore

Select your Fiat model below for the correct inner CV joint:

With a comprehensive catalogue, selecting your model is the natural next step. Choosing your specific car directs you to components tailored precisely to its drivetrain layout and technical configuration.

Navigating to your model page provides detailed technical specifications. Covering everything from older classics to modern commercial vehicles, we ensure you find the right part whatever Fiat you drive. Our catalogue helps you navigate spline counts and joint designs with complete confidence.

Why buy from cvjoint24.com

Choosing cvjoint24.com means choosing an international shop backed by Swedish driveline specialists with a central warehouse in Helsingborg, Sweden, delivering swiftly across the EU. We understand the importance of receiving the correct car parts without delay, keeping an extensive inventory ready for rapid dispatch. With deep coverage of inner CV joints for Fiat, we offer availability that few general retailers can equal. Our ethos centres on providing dependable components, supported by knowledgeable customer support with hands-on technical expertise.

Every order is supported by our fitment guarantee, giving you total peace of mind when purchasing. As driveline specialists, we supply parts built to endure demanding European road conditions throughout every season. We combine the wide choice of a major stockist with the attentive advice of dedicated specialists, making us a dependable partner for your Fiat. Order securely and keep your car running smoothly with long-lasting, vibration-free performance.

Frequently Asked Questions about Inner CV Joints for Fiat

How do I know if the inner CV joint on my Fiat is failing?

The most common symptom is noticeable vibration through the car under acceleration, typically at speeds between 50 and 90 km/h. The vibrations usually stop as soon as you lift off the accelerator.

Is there a difference in the inner CV joint between manual and automatic Fiat models?

Yes, the spline count (number of teeth) and overall physical dimensions frequently differ between manual and automatic gearboxes. Always select your Fiat's exact make, model and engine variant to ensure the correct fit.

Can I replace just the inner CV joint, or do I have to replace the complete drive shaft?

On most Fiat models, you can easily replace just the inner CV joint, which is a far more cost-effective solution than replacing the entire drive shaft.

Are the CV boot and grease included when I buy an inner CV joint from you?

Yes, our inner CV joints are supplied as complete kits with the matching CV boot, premium-grade grease and all necessary mounting hardware, including clamps.

Why does my Fiat shake under acceleration but run smoothly at a constant speed?

This is a classic symptom of a worn inner CV joint. When the joint is placed under load during acceleration, play in the worn internal tracks creates imbalance, resulting in vibrations.

How do I find the correct inner CV joint for my Fiat Croma?

The easiest way is to select your Fiat Croma's model year and engine variant in our search filter. This ensures you only see the parts that precisely fit your specific car.