Inner CV joints for Honda Accord

Find the right inner CV joint for your Honda Accord by selecting your exact make, model and engine. This category includes a comprehensive range of components designed for...

Products for Inner CV joints for Honda Accord

34 products
1 - 24 of 34
Item no.:247162
  • Position: Inner
  • Inner splines: 30
  • Seal diameter: 40 mm
  • Total length: 58,4 mm
  • Joint diameter: 80 mm
Item no.:145667
  • Position: Inner
  • Inner splines: 28
  • Seal diameter: 40 mm
  • Total length: 485,5 mm
  • Joint diameter: 90 mm
Item no.:244371
  • Position: Inner
  • Inner splines: 34
  • Seal diameter: 40 mm
  • Total length: 120 mm
  • Joint diameter: 84 mm
Item no.:140757
  • Position: Inner
  • Inner splines: 34
  • Seal diameter: 40 mm
  • Joint diameter: 84 mm
  • Outer splines: 27
Item no.:245653
  • Position: Inner
  • Inner splines: 34
  • Seal diameter: 42 mm
  • Total length: 122 mm
  • Joint diameter: 84 mm
Item no.:140492
  • Position: Inner
  • Inner splines: 34
  • Splines gearbox side: 29
  • Seal diameter: 40 mm
  • Outer diameter: 84 mm
Item no.:245670
  • Position: Front right, Inner
  • Inner splines: 32
  • Seal diameter: 40 mm
  • Total length: 58,5 mm
  • Joint diameter: 83 mm
Item no.:145058
  • Position: Front left, Inner
  • Inner splines: 32
  • Seal diameter: 40 mm
  • Total length: 152 mm
  • Joint diameter: 84 mm
Item no.:348503
  • Position: Front, Inner
  • Inner splines: 32
  • Seal diameter: 40 mm
  • Total length: 155,5 mm
  • Outer splines: 27
Item no.:0466115
  • Position: Inner
  • Inner splines: 27
  • Seal diameter: 40 mm
  • Outer splines: 32
Item no.:247952
  • Position: Front right, Inner
  • Inner splines: 30
  • Seal diameter: 40 mm
  • Total length: 152,5 mm
  • Joint diameter: 80 mm
Item no.:149954
  • Position: Front left, Inner
  • Inner splines: 30
  • Seal diameter: 40 mm
  • Total length: 156 mm
  • Joint diameter: 80 mm
Item no.:248646
  • Position: Front right, Inner
  • Inner splines: 32
  • Seal diameter: 40 mm
  • Joint diameter: 82 mm
  • Outer splines: 27
Item no.:147311
  • Position: Front left, Inner
  • Inner splines: 32
  • Seal diameter: 40 mm
  • Joint diameter: 82 mm
  • Outer splines: 27
Item no.:346857
  • Position: Front, Inner
  • Inner splines: 30
  • Seal diameter: 40 mm
  • Total length: 36 mm
  • Joint diameter: 83 mm
Item no.:643509
  • Position: Rear, Inner
  • Inner splines: 25
  • Seal diameter: 35 mm
  • Total length: 53,5 mm
  • Joint diameter: 66 mm
Item no.:647678
  • Position: Rear, Inner
  • Inner splines: 25
  • Seal diameter: 35 mm
  • Total length: 154,5 mm
  • Outer splines: 23
Item no.:549615
  • Position: Rear, Inner
  • Inner splines: 20
  • Seal diameter: 35 mm
  • Total length: 163,5 mm
  • Joint diameter: 69 mm
Item no.:140582
  • Position: Inner
  • Inner splines: 35
  • Seal diameter: 42 mm
  • Total length: 127 mm
  • Joint diameter: 89 mm
Item no.:145340
  • Position: Inner
  • Splines gearbox side: 29
  • Splines wheel side: 34
  • Total length: 159 mm
  • ABS teeth: 34
Item no.:340663
  • Position: Inner
  • Inner splines: 32
  • Seal diameter: 40 mm
  • Total length: 120,5 mm
  • Joint diameter: 84 mm
Item no.:247030
  • Position: Inner
  • Inner splines: 30
  • Seal diameter: 40 mm
  • Total length: 58,4 mm
  • Joint diameter: 80 mm
Item no.:241219
  • Position: Inner
  • Inner splines: 34
  • Seal diameter: 40 mm
  • Total length: 120 mm
  • Joint diameter: 84 mm
Item no.:149212
  • Position: Inner
  • Inner splines: 34
  • Seal diameter: 40 mm
  • Joint diameter: 84 mm
  • Outer splines: 27
Showing 1–24 of 34 products

Inner CV joints for Honda Accord

The Honda Accord is renowned for its reliability, but like any front-wheel-drive car, the drivetrain is subjected to substantial strain over time. The inner CV joint is a crucial link in this system that is often overlooked in favour of the outer joint. At CVJoint24, you will find a dedicated range tailored specifically for your Honda Accord. With carefully selected items, we cater to most requirements across this model series. Choosing the correct component is not merely a matter of function; it also preserves the balance and precision engineered into your Honda. We help you navigate the technical specifications to ensure your repair is done right first time with parts that truly stand up to the test.

What does an inner CV joint do on a Honda Accord?

The inner CV joint on a Honda Accord is mounted closest to the gearbox and plays a vital role in transmitting power. Its primary function is to transfer torque from the transmission to the drive shaft, whilst accommodating up-and-down suspension movement. Unlike the outer joint, which must handle wide steering angles, the inner joint works mainly to compensate for changes in length as the suspension articulates. This is often achieved using a tripod joint or a plunging ball design that allows the shaft to slide axially within the joint. Without a properly functioning inner constant velocity joint, power delivery becomes jerky and mechanical stress quickly damages both the gearbox and wheel bearings, making it a pivotal part of the vehicle's drivetrain.

Common signs of wear

When an inner CV joint begins to fail on your Honda Accord, it is typically felt through distinctive vibrations rather than noises. These vibrations usually appear under acceleration and tend to disappear entirely as soon as you lift off the throttle or coast. This is a clear contrast to a failing outer CV joint, which produces a clicking noise at full lock at lower speeds. If you notice the entire car shaking, particularly between 60 and 100 km/h under load, it is high time to inspect the inner joints. Ignoring this wear can cause consequential damage to the gearbox oil seals due to imbalance, and in the worst case, complete drive failure while travelling.

How to choose the correct inner CV joint

Identifying the correct inner CV joint requires careful attention, as specifications vary considerably. Over the years, Honda has used different suppliers and technical solutions depending on engine size and transmission type, with manual and automatic gearboxes often requiring different joints. The most critical check is the number of splines (teeth) both towards the gearbox and towards the drive shaft, as well as the diameter of the seal surface. Because variations can occur even within the same model year, we strongly recommend filtering by your car's make, model and engine variant. This isolates the parts technically verified for your specific car. If in any doubt, you can also compare the dimensions of your old part with the technical drawings and specifications provided on our product pages.

Related parts to inspect

Be sure to inspect these exact pages for the same vehicle when working on the inner CV joint:

When a drivetrain component shows signs of wear, neighbouring parts on the same car often require attention as well. By checking these exact pages for your Honda Accord, it becomes easier to determine whether the issue lies specifically with the inner CV joint or another adjacent section of the drivetrain.

This is particularly relevant on models where vibrations, play and strange noises can transfer symptoms across several parts in the same drivetrain assembly. A quick check of related categories minimises the risk of replacing the right type of component while overlooking a neighbouring part that contributes to the very same problem.

By inspecting these components at the same time, you ensure that your car remains dependable and that your new inner joint is not subjected to unnecessary strain caused by vibrations from other worn parts.

Why shop at CVJoint24?

CVJoint24 is the international shop of a Swedish driveline specialist, dispatching directly from our warehouse in Helsingborg, Sweden, to drivers across Europe. We understand that precise fitment is everything when dealing with technical components like CV joints. Our strength lies in deep category expertise and an unwavering commitment to quality products that meet or exceed original Honda specifications. By offering reliable navigation by vehicle make, model and engine, we minimise the risk of incorrect purchases and save you valuable time. We stock high-precision car parts to help your Honda Accord regain its original driving feel and stability. When you buy from us, you receive not just a spare part, but access to genuine technical know-how and a range built to withstand demanding conditions on European roads.

Frequently Asked Questions about Inner CV Joints for Honda Accord – Correct Fit for Your Drivetrain

What are the most common symptoms of a failing inner CV joint on a Honda Accord?

The most common symptom is vibration through the car under acceleration, particularly at higher speeds. The vibrations usually cease as soon as you release the accelerator pedal.

Can I replace just the inner CV joint, or does the entire drive shaft need replacing?

On most Honda Accord models, you can easily replace just the inner CV joint, provided that the drive shaft itself is neither damaged nor bent.

Why is it important to select the exact vehicle details when searching?

The Honda Accord features many different CV joint designs depending on the engine, gearbox and model year. Filtering by make, model and engine variant ensures you get the correct spline count and dimensions.

Are the CV boot and grease included when purchasing an inner CV joint from you?

Yes, our inner CV joints are supplied as complete kits, including the matching CV boot, high-quality grease and essential fitting hardware such as circlips.

What is the difference in symptoms between an inner and an outer CV joint?

A faulty inner CV joint causes shuddering and vibration under acceleration, whereas a worn outer CV joint produces a clicking or knocking noise when turning at low speeds.

How long does an inner CV joint last on a Honda?

Lifespan varies considerably, but as long as the CV boot remains intact to keep dirt and moisture out, they can last for many hundreds of thousands of kilometres. A split boot, however, quickly leads to premature wear.